1
3
Location of Controls
1. ON/OFF/DIMMER Switch
2. Battery Compartment Cover*
3. Light Sensor Switch
4. Light Sensor
*Underneath unit
Installation
Hook and Loop Tape (included)
1. Check the location of where you want to place the puck light. Make sure it is clean and that there is no debris or dust.
2. Place the two pieces of hook and loop tape together so that the hook and loop sides adhere to each other. There is a recessed area showing the
optimal position for the hook and loop tape.
NOTE:
Hook and loop tape may be cut to desired size for easier removal.
3. Remove the plastic covering on one sticky side of the tape.
4. Place the tape in the center of puck light base. This is the battery compartment side.
5. Remove the plastic covering on the other sticky side of the tape.
6. Place the puck light in the desired location. Press fi rmly and hold for fi ve (5) seconds so that the tape adheres to the surface.
CAUTION:
Be cautious of what surface the hook and loop adhesive is attached to, as it may remove paint or damage surface.
Screw (included)
1. Drill a pilot hole in the location where you want to mount the puck light. The hole should be where you want the center of the puck light to be located.
2. Put screw (included) in pre-drilled hole. Do not insert the screw all the way. Leave ½” of the screw out of the hole.
3. Slide battery cover over screw. Prongs should face down as shown.
4. Slide battery cover to the left or the right so that the neck of screw is in the narrow part of the hole. Tighten screw until battery cover is secure to sur-
face. Do not over tighten. Attach puck light body to battery cover.
Operating Directions
Light positioning
• The LED Puck Light’s base can be twisted 360°.
• Pivot the lens up to 30º to light desired area.
ON/OFF/DIMMER Operation
• Press power symbol once for full brightness.
• Press again for softer light.
• Press a third time to turn the light off.
Built-in Auto On Auto Off Light Sensor
The unit comes complete with a photocell light sensor. You may choose to activate this feature to avoid having to physically press the LED puck light On &
Off during each use. The Auto On Auto Off Light Sensor is designed to turn the LED puck light On automatically when ambient light is detected. The light
sensor will also shut the LED puck light off automatically when ambient light is no longer detected.
NOTE:
When using Auto ON Auto OFF Light Sensor the dimmer feature is temporarily deactivated.
An example of where and how you might choose to activate the Light Sensor is as follows:
Closet: Closet is dark and sealed from light when door is not open. Mount LED puck light in closet in desired position. Turn Light Sensor switch to either
position 1 or 2. Make sure that the light sensor is facing in the direction of the ambient light source. When closet door is opened and light is detected from
outside of closet, the LED puck light will turn On. When closet door is closed, LED puck light will go Off automatically.
NOTE:
Always test to make sure that the puck light is going ON and OFF properly when utilizing the light sensor function.
For best operation using Light Sensor:
1. Light Sensor Setting 0 (OFF): Light sensor is OFF. Activate and deactivate LED puck light manually.
2. Light Sensor Setting 1 (Light sensor 1 minute timer): Ambient light will turn the light on for 1 minute.
3. Light Sensor Setting 2 (Light sensor 5 minute timer): Ambient light will turn the light on for 5 minutes.
4. Place Light Sensor facing direction of ambient light source.
NOTE:
Refl ective materials in close proximity to the LED puck light may affect the light sensor feature. The refl ective materials may cause the light to stay
ON. This may occur in kitchen cabinets where dishes are refl ecting the light from the LED puck light. In these instances it may be best to point the light
sensor away from refl ective materials/areas. If the area is highly refl ective it is best not to use the Auto On Auto Off Light Sensor.
Inserting/Replacing the Batteries
If the LEDs appear to be dim this is an indication that your batteries need to be replaced.
To Install Batteries for the First Time:
Remove battery compartment housing at the back of the puck light. To do so, hold the front of the puck light in one hand, with the other hand grab fi nger
grips on battery compartment cover and pull away from puck light. The cover will pop off.
NOTE:
It may help to turn the light head or battery compartment cover clockwise or counter-clockwise as you are pulling it off.
To Replace Batteries Once Puck Light is Mounted:
1. Puck Light body will release from battery compartment cover/mounting bracket easily. Place fi ngers around Puck Light body and pull down gently to
release light head and expose battery compartment.
2. Remove old batteries (if replacing batteries).
3. Replace with three (3) new AAA batteries.
4. Make sure to follow battery polarity guide when installing new batteries.
5. Replace battery compartment housing.
Battery Precautions:
1. Use only the size and type of batteries specifi ed.
2. Always purchase the correct size and grade of battery most suitable for the intended use.
3. Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment. Reversed batteries may cause damage to
the device.
4. Do not mix alkaline, standard (Carbon-Zinc), or rechargeable (Nickel Cadmium) batteries.
5. Replace all batteries of a set at the same time. Do not mix old and new batteries.
6. Clean the battery contacts and also those of the device prior to battery installation.
7. Do not dispose of batteries in fi re.
8. Remove batteries if consumed or if product is to be left unused for an extended period of time.
LPL620XLL/LPL620WXLL/LPL623XLL/LPL623WXLL Series Owner’s Manual
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause undesired operation.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING:
Modifi cations to this product not approved by the party responsible for compliance could void the user’s authority to operate the product.
Limited Warranty
Under normal use and conditions, AmerTac provides to the original purchaser of this product a one year limited express warranty that is set
forth in the Limited Warranty stated in full at www.amertac.com/warranties. The Limited Warranty is in lieu of all other express or implied
warranties or liabilities subject to the exceptions explained fully in the Limited Warranty on the website.
Light Sensor Off
Capteur de lumière éteint
Sensor de luz desactivado
Light turns on for 1 minute
La lumière s’allume pendant 1 minute
La lámpara se enciende durante 1 minuto
Light turns on for 5 minutes
La lumière s’allume pendant 5 minutes
La lámpara se enciende durante
5 minutos
WIRELESS LED PUCK LIGHT
WITH LIGHT SENSOR
2
4
Finger Grips
(for Removing
Battery Compartment)
BATTERY
COMPARTMENT
COVER
Battery
Compartment
Cover
Main Unit
Puck Light Body
250 Boulder Dr.
Breinigsville, PA 18031
610-336-1330
www.amertac.com
Made in China / Fabriqué en
Chine / Fabricado en China
© 2018 AmerTac™
I18-0101-A
