background image

Ameritron RCS-10 

Instruction Manual 

The horizontal row is the “through ports”; the vertical row is “unwanted ports”: 
Ports 

25.8 

23.7 

39 

24.1 

43.5 

42 

56 

19.8 

31.1 

24 

37.9 

23.5 

56 

42.4 

19.8 

37 

25.5 

38.7 

58 

24.3 

44.4 

30.8 

19.5 

19.4 

54 

37.5 

37.3 

24.1 

19.4 

40.1 

38.4 

52 

25.4 

23.3 

39.6 

32.5 

18.9 

46 

38.8 

19.8 

30.7 

23.5 

35 

51 

19.6 

40.2 

19.7 

37.4 

25.2 

46 

32.4 

32.4 

19.1 

30.6 

19.4 

19.3 

 

Description 

 
The remote relay unit is designed for indoor or outdoor mounting.  It has a UV resistant 
ABS weather cover and corrosion resistant metal parts.  The mounting bracket assembly 
is designed to accept masts from 1 inch up to 2-1/4 inch outside diameter, but can also be 
attached to flat surfaces. 
 
The remote relay switch section is designed for 50-ohm systems, and operates from dc to 
60 MHz with very good performance. The RCS-10 can be used to 150 MHz, but only in 
non-critical applications. Examples of non-critical applications are switching antennas for 
local repeater or simplex operation. Examples of critical applications where the RCS-10 
could  cause  problems  would  include  long-distance  weak-signal  work  or  SWR  critical 
systems.  SWR  of  the  RCS-10  can  be  as  high  as  1.8:1  on  150MHz,  and  port-to-port 
isolation can be as low as 19dB.  
 
The  RCS-10  relay  switch  section  is  normally  supplied  with  high-quality  UHF-type 
connectors,  although  N-connector  models  are  available.    16-ampere  sealed  contactors 
easily handle power levels exceeding 1500 watts on frequencies below 60MHz, and over 
500 watts at 150MHz. Typical power handling below 30 MHz exceeds 5kW. 
 

IMPORTANT NOTE ABOUT CONNECTORS! 

Although type-N connectors improve weather sealing, they will 

not

 improve loss or SWR 

performance  of  this  switch.    Standard  UHF  connectors  have  negligible  loss,  and  have 
immeasurable affect on system SWR below upper VHF.  Type-N connectors may reduce 
power-handling capabilities of this switch. 

 
 
 
Control  signals  use  a  three-wire  system  (plus  ground).    The  control  signals  are  BCD 
encoded.  In  this  system  control  wires  are  labeled  A,  B  and  C,  and  operate  using  an 
assigned value of A=1, B=2, and C=4. By using this system, three wires can count from 
zero to seven. The relay box selects up to eight antennas using the following scheme: 
 

Summary of Contents for RCS-10

















Reviews: