Hex wench, supplied
8
To change direction of handle rotation,
proceed as follows:
Turn valve to OFF position.
Pull out INDEX CAP (1) and remove
HANDLE SCREW (2).
Pull off HANDLE (3) and unscrew
ESCUTCHEON BASE (4).
Remove SPRING CLIP (6).
Lift STOP WASHER (5), turn 90° and replace.
Replace SPRING CLIP (6).
Reinstall ESCUTCHEON (4) and HANDLE
ASSEMBLY.
If spout drips, operate handles several times
from OFF to ON position. Do not force - handles
turn only 90°.
90
$
SERVICE
9
5
6
HANDSHOWER INSTALLATION (Model 2555.901 series only)
TEST INSTALLED FAUCET
6
Turn VALVES "off" and attach handles.
Lift HANDSHOWER from HOLDER, direct spray into tub, lift
TRANSFER KNOB to check HANDSHOWER and HOSES for leaks.
Turn handles "off."
Drop SPRAY ESCUTCHEON (1) through the fourth hole of the tub ledge (12" max from SPOUT
center) with SPRAY ESCUTCHEON (1) directed towards tub center. Be sure RUBBER RING (2)
is properly seated in ESCUTCHEON (1). Install RUBBER WASHER (3) BRASS WASHER (4) and
LOCKNUT from underside of ledge.
Secure SPRAY ESCUTCHEON (1) by tightening LOCKNUT.
Add SEAL WASHER (5) and connect HOSE (10) to outlet nipple
at the bottom of COUPLING (7). Tighten firmly.
Slip SHOWER HOSE (8) with COUPLING NUT through SPRAY
ESCUTCHEON (1). Install SEAL (9) and connect both HOSES (8)
and (10), Connect HAND SHOWER (11) to SPRAY HOSE (8).
When not in use, HANDSHOWER should be seated
in the HOLDER.
NOTE
Before the bathroom is completely finished, you may
want to remove spout, handshower, and handles.
To remove handles, reverse steps in section 4.
To remove SPOUT (1), proceed as follows:
Lift TRANSFER ROD (2) and unscrew KNOB (3). (Model 2555.901only).
Remove PLUG BUTTON (4) and remove SET SCREW (5) using 5mm hex
wrench supplied.
Lift SPOUT (1) off SHANK (6) carefully and remove RUBBER RING (7).
Unscrew SHANK SLEEVE (8) and lift TRANSFER ROD (2) from
SHANK (6). (Model 2555.901only).
Reverse sequence to re-install SPOUT (1). Be sure RUBBER
RING (7) is properly seated in its recess at the base of the SPOUT (1).
Make certain SET SCREW (5) is properly aligned and tight so that
SPOUT (1) is locked in place.
7
5
With handles in "off" position, turn on water supplies and check
all connections for leaks.
Operate both handles and flush water lines thoroughly.
Check SPOUT mounting for leaks.
The flow rate of this Tub Filler exceeds 20 gallons/minute
at higher water pressure. Do not fill bathtub unattended.
CAUTION
1
2
3
4
5
5
7
8
10
9
9
11
1
2
3
4
6
7
6
8
4
3
2
1
. 3 F W
EverClean™ Finish Care
Instructions
American Standard’s EverClean finish
will wipe clean with a soft, dry cloth. A
soft cloth with clean water may also be
used, if desired. No additional cleaning
products are required.
DO NOT USE: Soaps, acid, polish,
abrasives, harsh cleaners, or a cloth
with a coarse surface.
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 (800) 442-1902
Weekdays 8:00 a.m. to 8:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Product names listed herein are trademarks of American Standard Inc.
© American Standard Inc. 2002
IN MEXICO 01-800-839-12-00
LOCKNUT
