American Standard SELECTRONIC 6065.121 Installation Instructions Manual Download Page 10

Page: 10 / 10

M968699 Rev. 1.3

HOT LINE FOR HELP

For toll-free information and answers to your questions, call:

1 (800) 442-1902

Weekdays 8:00 a.m. to 6:00 p.m. EST

IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)

Weekdays 8:00 a.m. to 7:00 p.m. EST

Product names listed herein are trademarks of AS America, Inc.

IN MEXICO 01-800-839-12-00

PRODUCT NUMBERS

A950223-0071600A

SENSOR ASSEMBLY

W/MTG. KIT.

FOR FLUSH VALVE

WITH1.6 gpf

A950223-0071280A

SENSOR ASSEMBLY

W/MTG. KIT.

FOR FLUSH VALVE

WITH1.28 gpf

A923654-0070A

BATTERY 6VCR-P2

M962666-0020A

MANUAL VALVE

M962664-0070A

SOLENOID ASSEMBLY

M962663-0070A

PISTON ASSEMBLY

A906680-0070A

BONNET NUT

A955066-0020A

ADJUSTABLE TAILPIECE

A955057-0020A

INLET PIPE ASSEMBLY

A955054-0020A

VACUUM BREAKER

ASSEMBLY (220mm)

A955068-0020A

VACUUM BREAKER

ASSEMBLY (610mm)

M962665-0021600A

COVER ASSEMBLY FOR

FLUSH VALVE WITH1.6 gpf

(BATTERY INCLUDED)

M962665-0021280A

COVER ASSEMBLY FOR

FLUSH VALVE WITH1.28 gpf

(BATTERY NCLUDED)

SELECTRONIC™

PROXIMITY TOILET

FLUSH VALVE

1.6 & 1.28 GPF

6065.161
6065.121
6065.565

6065.162
6065.122
6065.525

A955056-0020A

1" SUPPLY STOP

Summary of Contents for SELECTRONIC 6065.121











Search results

Summary of Contents for SELECTRONIC 6065.121

Reviews:

Related manuals for SELECTRONIC 6065.121

Brands by name

Popular brands

American Standard SELECTRONIC 6065.121, Installation Instructions Manual

Search results

Summary of Contents for SELECTRONIC 6065.121

Reviews:

Related manuals for SELECTRONIC 6065.121

Brands by name

Popular brands