background image

Installation InstructionsIn

s

t

a

ll

a

t

io

n

 I

n

s

t

r

u

c

t

io

n

s

(In Toronto Area only: 1-905-3061093)

Certified to comply with ASME A112.19.2M

© 2008 AS America, Inc.

NOTE TO INSTALLER: Please give this manual to the customer after installation.

SELECTRONIC™

PROXIMITY TOILET FLUSH VALVE

1.28 & 1.6 GPF

Exposed Flushometer
for 1-1/2

"

 Top Spud Bowls

CLOG RESISTANT

• Self-cleaning piston valve prevents clogging and reduces maintenance.

ONE SENSOR FITS ALL

• Only 1 sensor for entire Selectronic™ line of faucets, urinals, and flush valves.
• Range can be adjusted manually or with optional remote control.
• Sensor Features Low Battery Indicator.

M968699 Rev.1.3

6065.161
6065.121 
6065.565

MODEL NUMBERS

6065.162
6065.122
6065.525

CLOG RESISTANT

• Self-cleaning piston valve prevents clogging and reduces maintenance.

ONE SENSOR FITS ALL

• Only 1 sensor for entire Selectronic™ line of faucets, urinals, and flush valves.
• Range can be adjusted manually or with optional remote control.
• Sensor Features Low Battery Indicator.

To learn more about American Standard Faucets visit our website at: 

www.americanstandard-us.com

or U.S. customer's e-mail us at: 

[email protected]

For Parts, Service, Warranty or other Assistance, 

please call

 

1-800-442-1902 (In Canada: 1-800-387-0369)

(In Toronto Area only: 1-905-3061093)

In

s

t

a

ll

a

t

io

n

 I

n

s

t

r

u

c

t

io

n

s

Summary of Contents for SELECTRONIC 6065.121











Reviews: