INSTALL HANDLES (Lever)
INSTALL HANDLES (Cross)
CHECK DRAIN CONNECTIONS
11
12
13
14
TEST INSTALLED FITTING
With HANDLES
(1)
in OFF position, turn on WATER
SUPPLIES
(2)
and check all connections for leaks.
Remove AERATOR
(3)
.
Operate both HANDLES
(1)
to flush water
lines thoroughly.
Replace AERATOR
(3)
.
1
HOT
COLD
2
4
2
1
5
SERVICE
If spout drips, operate handles several
times from OFF to ON position. Do not
force - handles turn only 90˚.
“P” TRAP
WASTE
OUTLET
3
Operate POP-UP KNOB
(5)
and fill Sink with water. Check
that DRAIN STOPPER
(4)
makes a good seal and retains
water in Sink. If STOPPER
(4)
does not seal properly, please
refer to “Troubleshooting Guide” in these instructions.
Release POP-UP KNOB
(5)
down and check all drain
connections and
"P"
trap for leaks. Tighten
if necessary.
U S 6 0 4 0 4 R e v. 1 . 2
To change direction of handle rotation, proceed as follows:
Turn valve to OFF position.
Remove IINDEX
(1)
and HANDLE SCREW
(2)
.
Pull HANDLE
(3)
off.
Remove ADAPTER
(4)
.
Remove SPRING CLIP
(5)
.
Lift STOP WASHER
(6)
, turn 90˚ and replace.
Replace SPRING CLIP
(5)
.
Replace ADAPTER
(4)
, HANDLE
(2)
,
SCREW
(2)
, and INDEX
(1)
.
90˚
7
Push INDEX CAP
(4)
in hole of LEVER BALL
(6)
.
Secure HANDLE BASE
(2)
with HANDLE SCREW
(3)
.
1
2
5
3
4
6
Turn VALVE into OFF position.
Push ADAPTER
(1)
into HANDLE
BASE
(2)
in a way that the male
square on the ADAPTER
(1)
fits
in the female square of the
HANDLE BASE
(2)
.
Push HANDLE BASE
(2)
and
ADAPTER
(1)
onto VALVE STEM
(5)
.
Check alignment, if not satisfactory
aligned;
Turn VALVE into OFF position.
Push ADAPTER
(1)
into HANDLE
BASE
(2)
in a way that the male
square on the ADAPTER
(1)
fits
in the female square of the
HANDLE BASE
(2)
.
Push HANDLE BASE
(2)
and
ADAPTER
(1)
onto VALVE STEM
(5)
.
Check alignment, if not satisfactory
aligned;
Push out ADAPTER
(1)
carefully.
Turn ADAPTER
(1)
either 45˚ or 90˚
so that male square on ADAPTER
(1)
catches different female square in
HANDLE BASE
(2)
.
Push out ADAPTER
(1)
carefully.
Turn ADAPTER
(1)
either 45˚ or 90˚
so that male square on ADAPTER
(1)
catches different female square
in HANDLE BASE
(2)
.
1
5
3
3
4
6
7
4
2
WASHER
(PORCELIAN
CROSS
HANDLE ONLY)
Push INDEX CAP
(4)
in hole of METAL CROSS
(6)
or
PORCELAIN CROSS
(7).
Secure HANDLE BASE
(2)
and METAL
CROSS
(6)
or PORCELAIN CROSS
(7)
with HANDLE SCREW
(3)
.
4
2
1
3
5
4
10
DO: SIMPLY RINSE THE PRODUCT
CLEAN WITH CLEAR WATER.DRY
WITH A SOFT COTTON FLANNEL
CLOTH.
DO NOT: DO NOT CLEAN THE
PRODUCT WITH SOAPS, ACID,
POLISH, ABRASIVES, HARSH
CLEANERS, OR A CLOTH WITH
A COARSE SURFACE.
CARE INSTRUCTIONS:
