background image

M 9 6 8 3 0 5   R E V.   1 . 1

Thread FLANGE 

(1) 

counter-clockwise and remove

FLANGE 

(1) 

and FOAM GASKET 

(2) 

from drain

body. 

Fig.

 

A.

Thread LOCKNUT 

(3)

 clock-wise to bottom of

drain body. Push GASKET 

(4)

 down against

LOCKNUT 

(3). 

Fig.

 

B.

POP-UP DRAIN

Tighten TAILPIECE 

(4)

 on DRAIN BODY before

installing DRAIN BODY. 

Fig.

 

B.

6

2

4

3

2

TIGHTEN LOCKNUT

1

REMOVE FLANGE

Remove CLEAR PLASTIC COVER 

(1)

.

Remove CARDBOARD SPACER 

(2)

 from under

DRAIN POP-UP 

(3)

.

2

2

3

3

1

1

Tighten LOCKNUT 

(1)

 firmly with Adjustable

Wrench or Channel Locks.

INSTALL DRAIN FROM

BELOW FIXTURE

5

From under side of SINK
install DRAIN BODY 

(1)

 up

through drain outlet.

Note:

 No plumber’s putty

or caulk is required.
The CABLE ATTACHMENT
POINT 

(2)

 must face towards

the rear of the SINK.

Install FOAM GASKET 

(3) 

and

FLANGE 

(4)

 onto drain body

from above SINK and tighten
FLANGE 

(4)

 firmly.

4

Fig.

 

A.

Fig.

 

B.

Fig.

 

A.

Fig.

 

B.

REAR

OF

SINK

1

POP-UP KNOB 

(1)

 must be fully down. 

Fig.

 

B.

  

FLANGE GASKET AND POP-UP KNOB

WHITE FOAM

GASKET

NOT VISIBLE

DRAIN

FLANGE

Fig.

 

A.

Fig.

 

B.

Check DRAIN FLANGE in SINK to ensure that
WHITE FOAM GASKET 

(3)

 is fully compressed

and not visible. 

Fig.

 

A.

2

DRAIN

OUTLET 

1

3

4

DRAIN

BODY

4

DOWN

   0

   1

   2

  3

  4

   5

   6

  7

    

 

Summary of Contents for Centerset Lavatory Faucet with SpeedConnect Drain 1480.110

Page 1: ...ace Fig A Assemble LOCKNUTS 3 onto SHANKS 4 from under side of Sink Hand tighten firmly Fig B 2 2 4 3 3 4 1 HAND TIGHTEN Fig A Fig B 1 PUTTY IF REQUIRED Congratulations on purchasing your American Standard faucet with Speed Connect drain a feature found only on American Standard faucets Your new American Standard faucet is designed to work only with the Speed Connect drain Heplful tips for removin...

Page 2: ...Adjustable Wrench or Channel Locks INSTALL DRAIN FROM BELOW FIXTURE 5 From under side of SINK install DRAIN BODY 1 up through drain outlet Note No plumber s putty or caulk is required The CABLE ATTACHMENT POINT 2 must face towards the rear of the SINK Install FOAM GASKET 3 and FLANGE 4 onto drain body from above SINK and tighten FLANGE 4 firmly 4 Fig A Fig B Fig A Fig B REAR OF SINK 1 POP UP KNOB ...

Page 3: ...LL NOSE RISERS 3 Use adjustable wrench to tighten connections Do not over tighten Be careful not to kink copper supply when bending Use tubing cutter to cut to proper length Connect 1 1 4 O D tailpiece on POP UP DRAIN to waste outlet MAKE WATER SUPPLY AND WASTE CONNECTIONS 9 FERRULE 1 2 3 NOTE FLEXIBLE SUPPLIES OR BULL NOSE RISERS MUST BE PURCHASED SEPARATELY HOT COLD Thread CABLE CONNECTOR 1 cloc...

Page 4: ... To set the maximum hot water temperature of your faucets all you need to do is adjust the setting on the HOT LIMIT SAFETY STOP Loosen SET SCREW 2 with 2 5mm hex wrench Pull HANDLE 1 off valve stem Pull off CAP 3 Use a flat blade screwdriver or your fingers to pull up and rotate red HOT LIMIT SAFETY STOP 4 Follow Step A or B to adjust min max discharge temperature 0 being the hottest to 7 the cold...

Reviews: