American Standard BERWICK 7430.801 Installation Instructions Manual Download Page 7

Page: 7 / 8

M 9 6 8 6 4 0 R E V . 1 . 1

STOPPER INSTALLATION PROCEDURE

Locked Mode:

Look at the Plastic Loop at the bottom of the Stopper and notice
that the Loop is on one side of the Stopper.

Fig.

To install the stopper in

“Locked”

mode, insert the Stopper into

the Drain so that the Plastic Loop is facing toward the

rear

of the

Sink and the American Standard logo is facing

front

. Rotate

Stopper slightly if necessary so that the Stopper slides all the
way down.

Fig.

Re-install the Cam into the Drain, rotating the Cam if necessary
to make sure it is fully inserted.

Fig.

Re-install the Cam Cap, making sure the guide teeth are facing
outward. If the Cam Cap does not “snap” into place, then rotate
the Cam to make sure it is fully inserted.

Fig.

Re-attach Cable. See “CABLE ADJUSTMENT PROCEDURE” in
Troubling Shooting Guide to complete installation. Stopper will be
in

“Locked”

mode and not be removable.

Unlocked Mode:

Look at the Plastic Loop at the bottom of the Stopper and notice
that the Loop is on one side of the Stopper.

Fig.

To install the stopper in

“Unlocked”

mode, insert the Stopper into

the Drain so that the Plastic Loop is facing toward the

front

of the

Sink and the American Standard logo is facing

rear

. Rotate Stopper

slightly if necessary so that the Stopper slides all the way down.

Fig.

Re-install the Cam into the Drain, rotating the Cam if necessary
to make sure it is fully inserted.

Fig.

Re-install the Cam Cap, making sure the guide teeth are facing
outward. If the Cam Cap does not “snap” into place, then rotate
the Cam to make sure it is fully inserted.

Fig.

Re-attach Cable. See “CABLE ADJUSTMENT PROCEDURE” in
“Troublingshooting Guide” to complete installation. Stopper will be
in

“Unlocked”

mode and removable

The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be
removed) or “Unlock” Mode (Stopper is removable).

Unlocked Mode

LOOP TOWARD
FRONT OF SINK

180˚

LOGO

DRAIN

Fig.

Locked Mode

(Vandal Proof)

LOGO

DRAIN

Fig.

LOOP TOWARD
REAR OF SINK

Fig.

INSTALL
CAM CAP

CAM

INSTALL CAM

Summary of Contents for BERWICK 7430.801









Search results

Summary of Contents for BERWICK 7430.801

Reviews:

Related manuals for BERWICK 7430.801

Brands by name

Popular brands

American Standard BERWICK 7430.801, Installation Instructions Manual

Search results

Summary of Contents for BERWICK 7430.801

Reviews:

Related manuals for BERWICK 7430.801

Brands by name

Popular brands