7 3 0 5 1 3 - 1 0 0 R E V . D
RUBBER
GASKET
TANK MTG.
BOLTS PRE-
INSTALLED
NUT
WASHER
6b
8
7a
7b
a.
Install caps on washers. (If necessary, cut bolt height
to size before installing caps.)
b.
Smooth off the bead of sealant around base. Remove
excess sealant.
INSTALL TANK
a.
Install large rubber gasket over
threaded outlet on bottom of tank
and lower tank onto bowl so that
tapered end of gasket fits evenly into
bowl water inlet opening, and tank
mounting bolts go through mounting
holes. Secure with metal washers
and nuts.
b.
With tank parallel to wall, alternately
tighten nuts until tank is snugged
down evenly against bowl surface.
INSTALL TANK
a.
Install large rubber gasket over
threaded outlet on bottom of tank
and lower tank onto bowl so that
tapered end of gasket fits evenly into
bowl water inlet opening.
b.
Insert tank mounting bolts and
rubber washers from inside tank,
through mounting holes, and secure
with metal washers and nuts.
c.
With tank parallel to wall, alternately
tighten nuts until tank is snugged
down evenly against bowl surface.
INSTALL TOILET SEAT Install toilet seat in accordance with manufacturer's directions.
CLOSET
BOLT
CLOSET
BOLT
NUT
WASHER
BOLT CAP
RUBBER
GASKET
TANK MTG.
BOLTS
NUT
WASHER
!
- 2 -
CAUTION:
DO NOT OVERTIGHTEN NUTS MORE
THAN REQUIRED FOR A SNUG FIT!
!
CAUTION:
DO NOT OVERTIGHTEN NUTS MORE
THAN REQUIRED FOR A SNUG FIT!
For Tanks/Bowls using Speed
Connect System (Tank
mounting bolts pre-installed).
For all other Tanks/Bowls
RUBBER
WASHER
9a
9b
Before continuing, determine the type of water supply connecation you have from
the chart below and use the appropriate assembly parts required to properly
reconnect the water supply. DO NOT use plumber's putty to seal these fittings.
CAUTION: DO NOT USE
CONE WASHER WITH
PLASTIC SUPPLY LINE.
These parts must be used as
illustrated to insure water-tight
connection. Use of existing
coupling nut may result in
water leakage. Water supply
tube or pipe must extend at
least 1/2" inside threaded
shank of valve (does not apply
to flanged tubing).
Use existing
coupling nut
and washer.
Use existing spiral
cone washer.
Fluidmaster cone
washer may not
seal completely on
spiral type supply
line.
Captive cone
washers already
included. No
additional washers
needed.
CAUTION: Overtightening of
LOCK NUT or COUPLING NUT
could result in breakage and
potential flooding.
METAL/COPPER
FLARED TUBING
METAL FLANGED
TUBING
METAL SPIRAL
TUBING
VINYL/BRAIDED
CONNECTOR
LOCK NUT
LOCK NUT
LOCK NUT
LOCK NUT
COUPLING
NUT
COUPLING
NUT
EXISTING
COUPLING
NUT
COUPLING
NUT
WATER
SHUT-OFF
WATER
SHUT-OFF
WATER
SHUT-OFF
WATER
SHUT-OFF
CONE
WASHER
EXISTING
CONE
WASHER
EXISTING
WASHER
With correct washers in place
(see Step 9a), tighten
COUPLING NUT 1/4 turn beyond
hand tight. DO NOT
OVERTIGHTEN.
NUT
WASHER
COVER
MTG. CLIP
COVER
a.
Press covers over mounting clips. (If necessary,
cut bolt height to size before installing covers.)
b.
Smooth off the bead of sealant around base.
Remove excess sealant.
INSTALL BOLTS AND CAPS
HERITAGE 2176
Ellisse 2184
Baby Devoro 2315
Deco 2059
Cadet III 13L 2650/2660
Sonoma 2454
