manualshive.com logo in svg

American Dynamics SpeedDome RASEL Series, Installation And Service Manual, Page: 13 / 14

Share
Download
American Dynamics SpeedDome RASEL Series Installation And Service Manual Download Page 13

 

SPEEDDOME OPTIMA LT INDOOR CAMERA DOME INSTALLATION AND SERVICE GUIDE (8200-0181-01, REV. C) 

13 of 14 

Electrical Specifications 

Power Line 

Input voltage .......................... 18–30Vac, Class 2 

Limited Power Source 

Design tolerance .................... 16–36Vac 
Line frequency ....................... 50/60Hz 
Power consumption................ 21W max. 
Power on inrush current ......... 3A 
Allowable drop out:................. 33ms 
Connector: ............................. Plug-in Euro-style terminal 

block 5.08mm 

Max. cable distance ............... See chart on page 4. 

Surge Protection 

Video output........................... Gas discharge tube rated 

at: 

· 

8/20µs impulse 
discharge current: 10kA 

· 

Ten 8/20µs impulses 
discharge current: 5kA 

3.9 ohm series resistors 
Low capacitance Zener 
suppressor 6.5V 1500W 

Power line .............................. Gas discharge tube 

impulse rated at:  

· 

8/20µs impulse 
discharge current: 10kA 

· 

Ten 8/20µs impulses 
discharge current: 5kA 

TVS rated at 60V, 250A, 
1.5 Joules, 8/20µs 
impulse 

SensorNet/Manchester .......... Gas discharge tube 

impulse rated at:  

· 

8/20µs impulse 
discharge current: 10kA 

· 

Ten 8/20µs impulses 
discharge current: 5kA 

Isolation transformer 
coupled, 2000Vrms 
PTC resettable fuse 
protects transformer 
TVS rated at 5.6V, 40A, 
0.1 Joules, 8/20µs 
impulse 

SensorNet Communications 

Address range ........................ 0 to 255 
Bit rate: ................................... 230.4Kbps 
Network distance.................... 1km  
Maximum loads ...................... 32 per node 
Node repeaters....................... SensorNet junction boxes 
Cable topologies..................... Daisy chain 

Backbone 
Star 

Transmission medium ............ Single non-polarized 

unshielded twisted pair 
UTP 22AWG 

Wire configuration................... Single unshielded twisted 

pair UTP 22AWG non-
polarized 

Connector:.............................. Plug-in Euro-style terminal 

block 5.08mm 

Terminating resistor ............... 120 ohms, switch 

selectable 

Manchester Communications 

Address range ........................ 1 to 64 
Bit rate .................................... 31Kbps 
Network distance.................... 1.5km  
Maximum loads ...................... 32 per node 
Node repeaters....................... SensorNet junction boxes 
Cable topology........................ Daisy chain 
Transmission medium ............ Single polarized twisted 

pair 18AWG (Beldon 
8760) 

Connector............................... Plug-in Euro-style terminal 

block 5.08mm 

Terminating resistor ............... 120 ohms, switch 

selectable

 

Summary of Contents for SpeedDome RASEL Series















Reviews:

No comments