manualshive.com logo in svg

American Dynamics SensorRail IIIE, Service Manual

Share
Download
American Dynamics SensorRail IIIE Service Manual Download Page 25

 

SENSORRAIL IIIE 

8200-0593-03, REV. A 

SERVICE GUIDE 

25 of 34

 

RF Attenuator 

(dc to 6GHz usable) 

 

The RF attenuator is located at the transmit 
antenna on the trolley. 

CAUTION:

 The attenuator is required 

to comply with the CE regulation. 

Rail 
Distance 

RF 
Attenuator 

Part 
Number 

10–45m 30dB 

ADSMA30DB 

50–75m 20dB 

ADSMA20DB 

75–100m 

10dB or 15dB 

ADSMA10DB 
ADSMA15DB 

 

 

Note:

 There are environmental circumstances that 

may require a different value. 

Light Reduction Kit 

SR3-END-COVER and ADRL3BUL3.5U 

This kit prevents light reflections from entering the 
cowling from each end of the rail. 
1.  Mount the ection onto the existing rail using the 

hardware provided. 

2.  Attach the top hat to the top of the section to 

cover the large cutout. 

3.  Add extra cowling to the rail structure. 
4.  Attach the new end cover. 

Note:

 be sure to follow the installation guide for 

minimizing light reflections into the cowling. 

IMPORTANT!

 Ensure the customer understands 

that if installation requirements are not met, some 
light reflections cannot be removed from the 
picture on the video monitor. 

 

Old metal end 
cover shown. 

Summary of Contents for SensorRail IIIE



































Reviews:

No comments

Brands by name

Popular brands

Load more brands