manualshive.com logo in svg

American Dynamics RAS918LS, Installation And Service Manual, Page: 27 / 37

Share
Download
American Dynamics RAS918LS Installation And Service Manual Download Page 27

 

SPEEDDOME ULTRA VII EIS DAY/NIGHT CAMERA DOME 

8200-0184-14, REV. A 

INSTALLATION AND SERVICE GUIDE 

27 of 37 

Removing the P/S Board 

CAUTION:

 Electrostatic-sensitive device. Use a 

ground strap when handling power supply board. 

Referring to Figure 25. 

1.  Perform procedure "Removing the CPU Board" 

(page 26). 

2.  Remove metal shield. 

Remove three standoffs holding metal shield, 
gently remove power supply cable grommet 
from shield, then "gently" lift shield out of 
housing.  

CAUTION:

 Do not pull delicate cables attached 

to power supply board. 

3.  Detach fan motor cable. 

Cable connects to connector CN3 on power 
supply board. 

4.  Remove power supply board. 

Remove three standoffs, then remove power 
supply board from housing. 

5.  Reverse steps to reassemble. 

Figure 25. Removing the P/S board 

 

Removing the Pan Motor 

Referring to Figure 26. 

1.  Perform procedure "Removing the CPU Board" 

(page 26). 

2.  Perform procedure "Removing the P/S Board" 

(page 26). 

3. Remove pan motor. 

Lift motor housing up as shown (1) to disengage 
motor from pan gear. Then pull motor bracket 
towards outside of housing (2) to remove. 

4.  Reverse steps to reassemble. 

CAUTION:

 When putting in a new motor, be 

careful to properly mesh motor and pan gears! 
Failure to do so can destroy both motor and pan 
gear. Verify pan gear turns freely! 

 

Figure 26. Removing the pan motor  

1

2

 

Pan Motor 
(lift up, 
then out) 

Summary of Contents for RAS918LS






































Reviews:

No comments