American Dynamics MegaPower 48 Plus Installation Manual Download Page 35 | Manualshive

Page: 35 / 64

background image

35

Installation Manual

Direct Alarm and Relay Connections

Relay Outputs

The MegaPower 48+ patch panel provides a section for direct connection to two normally-open or normally-closed relay
outputs for switching of auxiliary devices such as lights, gates, audio alerts, recorders, etc.

Patch Panel Alarms

The MegaPower 48+ patch panel provides 16 screw terminals and corresponding ground returns for direct connection
to normally-open alarm contacts. These connections are referred to as “patch panel” alarms. Patch panel alarms are
connected with shielded, two-wire cable. Both the shield and ground wires must be connected to the ground terminals
in the patch panel alarm section.

System Alarm Handling

The total alarm handling capability of a single MegaPower 48+ is provided by 16 patch panel alarms, 512 RS232 alarms
wired through the AD2096A Alarm Interface Unit, 192 dome alarms (up to 48 domes, with four alarm contacts per
dome), and up to 48 video loss alarms that are generated when a loss of video sync is detected at a video input.

See Drawing 23, Page 36 for typical direct alarm and relay connections to a single MegaPower 48+ unit.

«
...
33
34
35
36
37
...
»

Summary of Contents for MegaPower 48 Plus

































































Reviews:

No comments

Related manuals for MegaPower 48 Plus

Brand: D-Link Pages: 4

Brand: D-Link Pages: 2

Brand: B&K Pages: 2

Brand: B&B Electronics Pages: 45

BNI IOL-314-S52-P012

Brand: Balluff Pages: 22

Brand: hager Pages: 2

Brand: hager Pages: 4

Brand: hager Pages: 2

Brand: GALCO Pages: 22

Brand: IOGear Pages: 10

Brand: Eaton Pages: 2

FlowPoint 2100 12

Brand: Cabletron Systems Pages: 36

Brand: Hawking Pages: 2

Antenna-Disconnect-Switch

Brand: ADS Pages: 12

Brand: Jerguson Pages: 4

Valena Life LE-752107

Brand: LEGRAND Pages: 5

Brand: ATEN Pages: 15

Brand: Tripp Lite Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands