8000-0982-02, Rev. C
Installation Instructions
AD T
OUCH
T
RACKER
®
16
Installation Instructions
1
T
OUCH
T
RACKER
with Multiplexer
PARTS REQUIRED
AD T
OUCH
T
RACKER
16 Installation Kit:
Part Number 0351-0474-06
Description
Qty.
Part No
.
Modular cable assy
4.3m
6003-0047-01
Screw, M2.9x9.5
1
5899-0004-102
Anchor, 4-8x.750
2
2880-0083-01
Screw, #8x1
2
2816-7634-44
Conn, 1x5pos
1
2109-0254-04
Lug, 22-16AWG
3
2141-0002
Cable, 3-cond, 18AWG
5m
6002-0024-01
Interconnect box
1
0300-1000-01
Multiplexer cable assy
1
0650-1079-01
Hood, D-Sub, 9pos, cable
1
2125-0007-02
Conn, D-Sub, plug, hsg, 9pos
1
2130-0021-01
Contact, pin, D-Sub, 22-26 AWG
1
2103-0092-01
!
WARNING Shock Hazard!
Disconnect AC Power to the Switch.
!
CAUTION static sensitive
components!
Follow proper handling procedures
to prevent component failure.
Installation Procedures
1.
Terminate the external interconnect module (EIM) at
the end of the SensorNet network. See the diagram on
page 2.
For more information on the SensorNet network, refer
to the SensorNet Network Guide (PN 8000-0970-01).
2.
Mount each EIM on a wall or other surface within 3m
(10') of the T
OUCH
T
RACKER
controller.
3.
Connect the power transformer and SensorNet cable to
J3 on each EIM.
4.
Wire the DB9 connector to the data cable. If you are
using a multiplexer with a DB25 connector, refer to the
illustration on page 2. If you are using a multiplexer with
a RJ11 connector, refer to the illustration on page 3.
5.
Connect the data cable from J1 on the main T
OUCH
T
RACKER
EIM to the Remote port at the rear panel of
the multiplexer.
6.
Connect the modular cable from J2 on EIM to the
T
OUCH
T
RACKER
controller.
7.
Connect the SensorNet cable from the dome to the
terminated EIM.
8.
Plug each power transformer into a grounded, 3 wire
receptacle.
NOTE:
If the keypad and backlighting do not illuminate
when power is applied, unplug each power transformer
and repeat steps 3 through 8.
9. From the T
OUCH
T
RACKER
controller, press
Menu
to configure the software for the multiplexer.
10. Using the Tracker Ball, page down the screen to
the
Config Devices
menu option.
11. Press the zoom/focus button to select the
Config Devices
menu option.
12.
Press
Next
to the select the appropriate device
for this installation. See the example screen
below.
Device = Mux 16
= POSEM
13. Press
Menu
to select the device configuration and
return to the Camera Control mode.
14. To configure the T
OUCH
T
RACKER
controller as a
primary or secondary unit, page down the screen to the
Tog Primary/2nd
menu option.
15. Press the zoom/focus button to select the
Tog Primary/2nd
menu option.
16. Press
Next
to toggle between using the T
OUCH
T
RACKER
controller as the primary (Main) unit for the
SensorNet polling and alarm monitoring or as the
secondary (Call) unit with limited user functionality.
17. Press
Menu
to reset the T
OUCH
T
RACKER
controller as
a primary or secondary unit. The controller will reboot
to the Camera Control Mode.
