American Dynamics ADSDUHOC Installation Manual Download Page 10

 

SPEEDDOME ULTRA OUTDOOR HOUSING 

8200-0492-02, REV. B 

INSTALLATION GUIDE - CONTINUATION 

12 of 12

 

Declarations 

Regulatory Compliance 

REG ID: SV SDUO 

Emissions .............................. 47 CFR, Part 15, Class A 
 ICES-003 
 

CISPR 22, Class A 

Immunity ...................................................... EN50130-4 
Safety ................................................................UL1950 
 

CSA C22.2 No. 950 

 EN60950-1 
 IEC 

60950-1

 

FCC COMPLIANCE:

 This equipment complies with Part 15 

of the FCC rules for Class A digital devices when installed and 
used in accordance with the instruction manual. Following 
these rules provides reasonable protection against harmful 
interference from equipment operated in a commercial area. 
This equipment should not be installed in a residential area as 
it can radiate radio frequency energy that could interfere with 
radio communications, a situation the user would have to fix at 
their own expense. 

EQUIPMENT MODIFICATION CAUTION:

 Equipment 

changes or modifications not expressly approved by 
Sensormatic Electronics Corporation, the party responsible for 
FCC compliance, could void the user's authority to operate the 
equipment and could create a hazardous condition. 

Other Declarations 

Thank you for using American Dynamics products. We 
support our products through an extensive and worldwide 
network of dealers. The dealer, through whom you originally 
purchased this product, is your point of contact if you have a 
need for service or support. Our dealers are fully empowered 
to provide the very best in customer service and support. 
Dealers should contact American Dynamics at (800) 507-6268 
or (561) 912-6259 or on the web at 
www.americandynamics.net. 

WARRANTY DISCLAIMER:

 Sensormatic Electronics 

Corporation makes no representation or warranty with respect 
to the contents hereof and specifically disclaims any implied 
warranties of merchantability or fitness for any particular 
purpose. 

NOTICE: 

The information in this manual was current when 

published. The manufacturer reserves the right to revise and 
improve its products. All specifications are therefore subject to 
change without notice. 

LIMITED RIGHTS NOTICE:

 For units of the Department 

of Defense, all documentation and manuals were developed at 
private expense and no part of it was developed using 
Government Funds. The restrictions governing the use and 
disclosure of technical data marked with this legend are set 
forth in the definition of “limited rights” in paragraph (a) (15) 
of the clause of DFARS 252.227.7013. Unpublished - rights 
reserved under the Copyright Laws of the United States. 

TRADEMARK NOTICE:

 

American Dynamics

 and 

Sensormatic

 are trademarks or registered trademarks of 

Sensormatic Electronics Corporation. Other product names 
mentioned herein may be trademarks or registered trademarks 
of Sensormatic or other companies. 

COPYRIGHT:

 Under copyright laws, the contents of this 

manual may not be copied, photocopied, reproduced, 
translated or reduced to any electronic medium or machine-
readable form, in whole or in part, without prior written 
consent of Sensormatic. 

MDR 07/2007 

 

www.americandynamics.net 

Summary of Contents for ADSDUHOC











Reviews: