American Dynamics AD715LS Series Installation And Service Manual Download Page 1

Installation and Service Guide

© Sensormatic 2000 (40 pages).

DeltaDome II  Camera Dome

8000-2708-01, REV. B

1

DeltaDome

 II

Programmable
Surveillance Camera

AD716LS and AD715LS Series

Figure 1. SpeedDome Ultra camera dome

American Dynamics

DeltaDome

, and the 

AD

 

logo

 are

registered trademarks of Sensormatic Electronics Corporation.
Other product names (if any) mentioned herein may be
trademarks or registered trademarks of other companies.

No part of this guide may be reproduced in any form without
written permission from Sensormatic Electronics Corporation.

(c) Copyright 2000. All rights reserved.

MDR 6/00

Contents

About this Guide.................................................... 1

About the Camera Dome ...................................... 2

Data Cable Requirements..................................... 8

Install/Removal Tool for ADIOB Base ................... 8

Power-Up Routine ................................................. 9

Synchronizing Domes ........................................... 9

Diagnostic LEDs.................................................... 9

Warnings and Cautions....................................... 10

Indoor Installation ................................................ 12

Using the Install/Removal Tool ........................... 20

Troubleshooting Indoor Domes........................... 22

Ordering Parts ..................................................... 34

Specifications-Indoor Dome ................................ 36

Specifications-Outdoor Housing.......................... 37

Specifications-22X Camera................................. 37

Declarations ........................................................ 38

About this Guide

This guide explains how to connect the camera
dome to a mounting base and how to service it.

It does not explain how to:

  Determine a mounting location for the camera

dome. The mounting location is determined by
customer requirements; therefore, this
information is provided separately.

  Attach the mounting base. There are two types

of mounting bases. See information shipped
with the base.

  Assemble housings and structures used with

this dome. See information shipped with the
housing and structure.

  Program the dome. See operator's guide

shipped with the dome.

Mounting
Base

Housing

Eyeball

Summary of Contents for AD715LS Series









































Reviews: