American Dynamics AD2091 Installation Instructions Manual Download Page 15 | Manualshive

Page: 15 / 16

American Dynamics AD2091 Installation Instructions Manual Download Page 15

DECLARATION OF CONFORMITY

According to ISO/IEC Guide 22 and EN45014

Manufacturer’s Name:

Sensormatic Electronics Corporation

Manufacturer’s Address:

1 Blue Hill Plaza
2

nd

Floor

Pearl River, New York, 10965 USA

Declares, that the product listed below:

Name/Type:

MegaPower Code Converter

Model Number:

AD2091-1

complies with all applicable directives as demonstrated by conformance to the following Product Specifications:

Safety:

EN 60950: 1992

EMC:

EN 50130-4: 1995
EN 55022: 1994 , Class B
EN 61000-3-2: 1995
EN 61000-3-3: 1995
EN 61000-4-2: 1995
EN 61000-4-3: 1996
EN 61000-4-4: 1995
EN 61000-4-5: 1995
EN 61000-4-6: 1996
EN 61000-4-11: 1994

Supplementary Information:

The products herewith comply with the requirements of the Low Voltage Directive, 73/23/EEC as amended by
93/68/EEC, and the EMC Directive, 89/339/EEC as amended by 93/68/EEC.

Pearl River, NY, USA

15 December, 2000

Harold D. Johnson, Ph.D.
Director of Engineering

European Contact: Sensormatic France S.A.

7, rue Alexis de Tocqueville, Parc de Haute Technologie, 92183 ANTONY CEDEX

«
...
13
14
15
16
»

Summary of Contents for AD2091

















Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands