background image

16

2. Single Dryer Venting

Where possible, it is suggested to provide a separate exhaust duct for each dryer.  The exhaust duct 

should

be 

laid out in such a way that the duct work travels as directly as possible to the outdoors with as few turns

as possible.  It is suggested that the use of 90° turns in the ducting be avoided; use 30° and/or 45° angles

instead.  The shape of the exhaust duct work is not critical so long as the minimum cross section area is

provided.

IMPORTANT:

For a dryer that is vented horizontally, the minimum duct size for a gas dryer is

14-inches (35.56 cm) for a round duct or 12-1/2” (31.75 cm) for a square duct.  The

minimum duct size for a steam dryer is 16-inches (40.64 cm) for a round duct or

14-1/2” x 14-1/2” (36.83 cm x 36.83 cm) for a square duct.  

THE DUCT SIZE

MUST NOT BE REDUCED ANYWHERE DOWN STREAM OF THE

DRYER

.

IMPORTANT:

Exhaust back pressure measured by a manometer at each basket (tumbler) exhaust

duct area 

should not exceed 

0.3 inches of water column (0.74 mb).

It is suggested that the duct work from each dryer not exceed 15 feet (4.57 meters) with no more than two

(2) elbows (excluding dryer connections and outside exhaust outlets).  If the duct work exceeds 15 feet

(4.57 meters) or has numerous elbows, the cross section area of the duct work 

must be 

increased in

proportion to the length and number of elbows in it.  In calculating duct size, the cross section area of a

square or rectangular duct 

must be

 increased by twenty percent (20%) for each additional 15 feet (4.57

meters).  The diameter of a round exhaust duct 

should be 

increased ten percent (10%) for each additional

15 feet (4.57 meters).  Each 90º elbow is equivalent to an additional 30 feet (9.14 meters), and each 45º

elbow is equivalent to an additional 15 feet (4.57 meters).

All manuals and user guides at all-guides.com

Summary of Contents for Gas/Steam Models ML-82






















































Reviews: