background image

User Instructions

  1/14

Octo Beam WW

©2013 ADJ Products, LLC all rights reserved. Information, 

specifications, diagrams, images, and instructions herein are 

subject to change without notice. ADJ Products, LLC logo and 

identifying product names and numbers herein are trademarks 

of ADJ Products, LLC. Copyright protection claimed includes all 

forms and matters of copyrightable materials and information 

now allowed by statutory or judicial law or hereinafter granted. 

Product names used in this document may be trademarks or 

registered trademarks of their respective companies and are 

hereby acknowledged. All non-ADJ Products, LLC brands and 

product names are trademarks or registered trademarks of their 

respective companies.
ADJ Products, LLC and all affiliated companies hereby dis-

claim any and all liabilities for property, equipment, building, and 

electrical damages, injuries to any persons, and direct or indi-

rect economic loss associated with the use or reliance of any 

information contained within this document, and/or as a result 

of the improper, unsafe, unsufficient and negligent assembly, 

installation, rigging, and operation of this product.

Europe Energy Saving Notice

Energy Saving Matters (EuP 2009/125/EC)

Saving electric energy is a key to help protecting the enviroment. 

Please turn off all electrical products when they are not in use. To 

avoid power consumption in idle mode, disconnect all electrical 

equipment from power when not in use. Thank you!

Summary of Contents for Octo Beam WW











Reviews: