![background image](http://html1.mh-extra.com/html/american-dj/gobo-splash/gobo-splash_user-instruction_2923098003.webp)
©
American DJ
®
- www.americandj.com - Gobo Splash Instruction Manual Page 5
©
American DJ
®
- www.americandj.com - Gobo Splash Instruction Manual Page 6
Gobo Splash
Fuse & Lamp Replacement
Gobo Splash
Operation
Power Supply:
Before plugging your unit in, be sure the source
voltage in your area matches the required voltage for your American
DJ
®
Gobo Splash before attempting operation.
General Operation:
Just plug this light in, and watch it go. This fix-
ture is designed to operate as a stand alone unit. It has been tested
and the lamp has been installed at the factory there is no assembly
necessary. The Gobo Splash is ready to be plugged in, out of the
box. There is no power switch, after plugging in the unit the lamp
should turn on, and unit will begin to function. If there is no lamp out-
put check the fuse and bulb. If the fuse and bulb are good, please
return the unit for servicing.
Operating Modes:
This unit comes with a 3-way multi-operating switch located on the
bottom of the unit. The switch controls three (3) different operating
modes; Static, Sound Active, and Continuous Rotation.
Switch in the "I" position: Mode 1 - In this mode the gobo wheel and
the external mirror dish will spin continuously in one direction, regard-
less of the presence of sound.
Switch in the “0” position: Mode 2 - In this mode the gobo wheel will
continuously rotate while the external mirror dish will remain static. In
this mode the unit may be used as a rotating-gobo projector.
Switch in the “II” position: Mode 3 - In the this mode the gobo wheel
will continuously rotate in one direction while the outer mirror dish will
react to sound. Please note that tapping on the unit, or high pitched
sounds may not trigger the unit, the unit is designed to react to low
frequencies (bass). Also note that the music sensitivity is preset at the
factory and may not be changed or adjusted.
Focusing:
The unit has a fully focusing lens. The lens is focused by manually
turning the knob located on the front, in either a clockwise or coun-
ter-clockwise direction.
Caution:
Always replace with the exact same type lamp and fuse,
unless otherwise specified by an authorized American DJ
®
techni-
cian. Replace with anything other than the specified part can damage
your unit and will void your manufactures warranty.
Warning:
If after you have replaced the lamp or the fuse and you
continue to blow either one, STOP using the unit. Contact customer
support for further instructions, you may have to return the unit for
servicing. Continuing to use the unit may cause serious damage.
Fuse Replacement:
First uplug the power. The fuse holder is locat-
ed above the power cord. Using a flat-head screw driver unscrew the
fuse holder. Remove the bad fuse and replace with a new one.
Lamp Replacement:
Caution! Never open the unit when in use.
Always disconnect the main power and allow the fixture ample time
to cool before attempting to replace the lamp. Lamp replacement has
been made simple by incorporating a split dome that is retained by
thumb screws.
Again, please remember to always replace with the
exact same type lamp.
1. Be sure to follow the proper procedures when handling halogen
lamps.
Never touch the new lamp with your bare fingers.
2. Unscrew the single thumb screw located at the rear of the unit.
3. Once the thumb screw has been removed, remove the lamp
cover plate to expose the lamp.
4. Remove and replace the lamp with an exact match.
5. Reassemble in reverse order.
Halogen Lamp Warning!
This fixture is fitted with
halogen lamps which are highly susceptible to
damage if improperly handled. Never touch the
lamps with your bare fingers as the oil from your
hands will shorten lamp life. Also, never move the
fixture until the lamps have had ample time to cool.
Remember, lamps are not covered under warranty
conditions.