©
American DJ Supply
®
- www.americandj.com - Fusion Scan 250™ User Manual Page 3
• Do not spill water or other liquids into or on to your unit.
• Be sure that the local power outlet match that of the required volt
age for your unit.
• Do not attempt to operate this unit if the power cord has been
frayed or broken. Please route your power cord out of the way of
foot traffic.
• Do not attempt to remove or break off the ground prong from
the electrical cord. This prong is used to reduce the risk of electrical
shock and fire in case of an internal short.
• Disconnect from main power before making any type of connection.
• Do not remove the top cover under any conditions. There are no
user serviceable parts inside.
• Never plug this unit in to a dimmer pack
• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.
• Do not attempt to operate this unit, if it becomes damaged in any
way.
• Never operate this unit when it’s cover is removed.
• To reduce the risk of electrical shock or fire, do not expose this unit
rain or moisture
• This unit is intended for indoor use only, use of this product out
doors voids all warranties.
• During long periods of non-use, disconnect the unit’s main power.
• Always mount this unit in safe and stable matter.
• Power Cord Protection - Power cords should be routed so they are
not likely to be walked on or pinched by items placed upon or
against them, paying particular attention to cords at plugs, conve-
nience receptacles, and the point where they exit from the unit.
• Cleaning - Follow the directions on page 14.
• Heat -The unit should be situated away from heat sources such
as radiators, heat registers, stoves, or other appliances (including
amplifiers) that produce heat.
Fusion Scan 250™
Safety Precautions
DANGER
VISIBLE LASER RADIATION
-AVOID DIRECT EYE EXPOSURE
LASER DIODE
WAVELENGTH : 635~650 nm
Max Output : <4.9mW
Class IIIa Laser Product
!
!
©
American DJ Supply
®
- www.americandj.com - Fusion Scan 250™ User Manual Page 4
Fusion Scan 250™
Safety Precautions
• The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The fixture does not appear to operate normally or exhibits a
marked change in performance.
The Fusion Scan 250™ features a bright 250 watt halogen bulb with
a separate gobo and color wheel and a green laser effect. The color
wheel features seven brilliant colors plus white and the gobo wheel
features 10 gobos plus a large spot. This fixture incorporates the
use of high quality stepper motors for a more accurate mirror move-
ment. Mirror movement allows for a full 90 degree tilt (vertical) and a
45 degree pan (horizontal). An internal built in microphone allows the
fixtures to run in Stand Alone mode so there is no need for an exter-
nal controller. The Fusion Scan 250™ may also be set-up to run in a
Master-Slave mode when used in multiples, up to four units. When
used in the Master-Slave mode, the unit will chase to several internal
programs. The Fusion Scan 250™ can also be controlled via a stan-
dard DMX controller such as the Elation
®
Show Designer,™ or the
Elation
®
DMX Operator,™ giving the user independent control over the
gobo and color wheel as well as the mirrors pan and tilt movements.
Note:
The built in programs in the Fusion Scan 250™ are so good you
may never need a DMX controller.
• ZB-ELC10 24V/250W
• DMX-512 Compatible.
• Stepper motors for smooth movements.
• 7 colors plus white.
• 10 Gobos plus spot.
• Green Laser
• Gobo Shake
• Master/Slave Operation
• Sound Active.
• Optional MINI/C controller, for blackout control.
• Optional Wireless MINI/C controller, for blackout control.
Fusion Scan 250™
Features
