ADJ Products, LLC - www.adj.com - Dotz Matrix User Manual Page 7
Dotz Matrix System Menu
ADJ Products, LLC - www.adj.com - Dotz Matrix User Manual Page 6
Notice:
Be sure to follow figures two and three when making your own
cables. Do not use the ground lug on the XLR connector. Do not con-
nect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
DMX512 IN
3-PIN XLR
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
DMX512
DMX+,DMX-,COMMON
1
2
3
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
1
2
3
1
2
3
DMX +
DMX -
COMMON
DMX512 OUT
3-PIN XLR
Figure 2
Figure 3
1 Ground
1 Ground
XLR Male Socket
XLR Pin Configuration
3 Hot
2 Cold
2 Cold
3 Hot
XLR Female Socket
Pin 3 = Data True (positive)
Pin 2 = Data Compliment (negative)
Pin 1 = Ground
Special Note: Line Termination.
When longer runs of cable are
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 90-120 ohm 1/4 watt resistor which is con-
nected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
DMX512 IN
3-PIN XLR
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
DMX512
DMX+,DMX-,COMMON
1
2
3
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
1
2
3
1
2
3
DMX +
DMX -
COMMON
DMX512 OUT
3-PIN XLR
Figure 4
5-Pin XLR DMX Connectors.
Some manufactures use 5-pin XLR
connectors for DATA transmission in place of 3-pin. 5-pin XLR fixtures
may be implemented in a 3-pin XLR DMX line. When inserting standard
5-pin XLR connectors in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.
Conductor
5-Pin XLR Male (In)
3-Pin XLR Female (Out)
Pin 1
Do Not Use
Do Not Use
Pin 3
Pin 2
Pin 1
Pin 3
Pin 2
Not Used
Not Used
Data True (+ signal)
Data Compliment (- signal)
Ground/Shield
3-Pin XLR to 5-Pin XLR Conversion
Dotz Matrix Set Up
STATIC COLOR
CL:RGB Flash00-99
Blackout,
Red-Green-Blue-Yellow-Cyan-Purple-White
Flash speed adjustable.
DREAM
Speed00-99 Flash00-99
Seven color dreaming
Speed & Flash adjustable
Speed00-99 Flash00-99
Seven color flow
Speed & Flash adjustable
FADE
Speed00-99 Flash00-99
Seven color fade
Speed & Flash adjustable
CHANGE
Speed00-99 Flash00-99
Seven color change
Speed & Flash adjustable
FLOW 1
Speed00-99 Flash00-99
Seven color chase
Speed & Flash adjustable
FLOW 2
Speed00-99 Flash00-99
Seven color chase
Speed & Flash adjustable
FLOW 3
Speed00-99 Flash00-99
Seven color chase
Speed & Flash adjustable
FLOW 4
Speed00-99 Flash00-99
Seven color chase
Speed & Flash adjustable
FLOW 5
Speed00-99 Flash00-99
Seven color chase
Speed & Flash adjustable
FLOW 6
Speed00-99 Flash00-99
Seven color chase
Speed & Flash adjustable
FLOW 7
Speed00-99 Flash00-99
Seven color chase
Speed & Flash adjustable
FLOW 8
Speed00-99 Flash00-99
Seven color chase
Speed & Flash adjustable
FLOW 9
Speed00-99 Flash00-99
Seven color chase
Speed & Flash adjustable
FLOW 10
Speed00-99 Flash00-99
Seven color chase
Speed & Flash adjustable
COLOR SNAKE
Built-In Programs
