![background image](http://html1.mh-extra.com/html/american-dj/dj-scan-250/dj-scan-250_user-instructions_2922683002.webp)
©
American DJ Supply
®
- www.americandj.com - DJ Scan 250™ Instruction Manual Page 4
©
American DJ Supply
®
- www.americandj.com - DJ Scan 250™ Instruction Manual Page 3
DJ Scan 250™
Quick Start
The DJ Scan 250™ features a bright 250 watt halogen bulb with a
separate gobo and color wheel. The color wheel features seven bril-
liant colors plus white and the gobo wheel features 10 gobos plus
a large spot. This fixture incorporates the use of high quality step-
per motors for a more accurate mirror movement. Mirror movement
allows for a full 90 degree tilt (vertical) and a 45 degree pan (hori-
zontal). An internal built in microphone allows the fixtures to run in
Stand Alone mode so there is no need for an external controller. The
DJ Scan 250™ may also be set-up to run in a Master-Slave mode
when used in multiples, up to four units. When used in the Master-
Slave mode, the unit will chase to several internal programs. The
DJ Scan 250™ can also be controlled via a standard DMX control-
ler such as the American DJ
®
Show Designer,™ or the American
DJ
®
DMX Operator,™ giving the user independent control over the
gobo and color wheel as well as the mirrors pan and tilt movements.
Note:
The built in programs in the DJ Scan 250™ are so good you
may never need a DMX controller.
• ZB-ELC7 24V/250W
• DMX-512 Compatible.
• Stepper motors for smooth movements.
• 7 colors plus white.
• 10 Gobos plus spot.
• Gobo Shake
• Master/Slave Operation
• Sound Active.
• Optional MINI/C controller, for blackout control.
• Optional Wireless MINI/C controller, for blackout control.
DJ Scan 250™
Features
Master/Slave Quick Start Stand Alone Mode
Connect up to four units together via XLR cables. The master unit will
run the slaves to the masters built in programs and internal micro-
phone. Plug in all units. When the DJ Scan 250™ is first turned on, it
will run through an internal self test where it resets all motors to their
zero position. After the self test the units will react to sound, and fol-
low several built in programs.
• Do not spill water or other liquids into or on to your unit.
• Be sure that the local power outlet match that of the required volt
age for your unit.
• Do not attempt to operate this unit if the power cord has been
frayed or broken. Please route your power cord out of the way of
foot traffic.
• Do not attempt to remove or break off the ground prong from
the electrical cord. This prong is used to reduce the risk of electrical
shock and fire in case of an internal short.
• Disconnect from main power before making any type of connection.
• Do not remove the top cover under any conditions. There are no
user serviceable parts inside.
• Never plug this unit in to a dimmer pack
• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.
• Do not attempt to operate this unit, if it becomes damaged in any
way.
• Never operate this unit when it’s cover is removed.
• To reduce the risk of electrical shock or fire, do not expose this unit
rain or moisture
• This unit is intended for indoor use only, use of this product out
doors voids all warranties.
• During long periods of non-use, disconnect the unit’s main power.
• Always mount this unit in safe and stable matter.
• Power Cord Protection - Power cords should be routed so they are
not likely to be walked on or pinched by items placed upon or
against them, paying particular attention to cords at plugs, conve-
nience receptacles, and the point where they exit from the unit.
• Cleaning - Follow the directions on page 10.
• Heat -The unit should be situated away from heat sources such
as radiators, heat registers, stoves, or other appliances (including
amplifiers) that produce heat.
• The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The fixture does not appear to operate normally or exhibits a
marked change in performance.
DJ Scan 250™
Safety Precautions