Introduction:
The Aggressor™ is a powerful effect for clubs, mobile
dj's, roller rinks and bowling alleys. The Aggressor™ especially looks
great in pairs. The Aggressor™ creates a dramatic cluster of 40 multi-
colored beams. This unit features an internal microphone that allows
the internal wheel to be triggered by sound, thus bouncing the colorful
beams of light up and down to the beat of the music. The Aggressor™
is fan cooled. For best result use this unit in conjunction with a fog
machine to enhance the beams.
Operating Instructions:
The Aggressor™ is ready to be hung or set
on the ground in a safe position. When mounting this unit to truss be
sure to use a clamp. Plug the unit in to a standard properly matched
power wall outlet. After plugging the unit in, the fixture will react to the
beat of the music via the sound active internal microphone. The unit
requires sound to activate the movement. The sound sensitivity is pre-
set at the factory to a moderate level and is not user selectable.
Caution!
Be sure not to obstruct cooling vents and keep this unit in a
well ventilated area. Never open the unit while in use. Avoid touching
the lamps, the lamp will get extremely hot under normal usage and
may cause serious injury.
Aggressor™
Operation
Please carefully read and understand the instructions in this manual
thoroughly, before attempting to operate this unit. These instructions
contain important safety information regarding the proper use and
maintenance of this unit. Please keep this manual in a secure place for
future reference.
Aggressor™
General Instructions
Aggressor™
Precautions
• Keep the outside of this device dry at all times. Do not spill water or
other liquids into or on to your unit. To prevent fi re or shock hazard,
do not expose this product to rain or moisture.
• Be sure to save the packing carton in the event you may have to
return the unit for service.
• This unit is designed for interior use only. Do not use this unit out
doors. Use of product outdoors will void the warranty.
• Be sure that the local power outlet match that of the required volt-
age for your unit.
• Never attempt to operate this unit if the power cord becomes frayed
or broken.
• Never attempt to operate this unit, if it becomes damaged in any
way.
• Always route your power cord out of the way of foot traffi c.
• Do not attempt to remove or break off the ground prong from the
electrical cord. This prong is used to reduce the risk of electrical
shock and fi re in the rare case of an internal short.
• Disconnect the unit’s main power when left unused for long periods
of time.
• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.
• Never block the ventilation holes.
• Never operate this unit when the cover is removed.
• This unit is for adult use only. Keep out of the reach of children.
Aggressor™
Halogen Lamp Warning
This fixture is fitted with halogen lamps which are
highly susceptible to damage if improperly handled.
Never touch lamp with your bare fingers as the oil
from your hands will shorten lamp life. Also, never
move the fixture until the lamps have had ample
time to cool. Remember, lamps are not covered
under warranty conditions.
©
American DJ Supply
®
- www.americandj.com - Aggressor™ Instruction Manual Page 4
©
American DJ Supply
®
- www.americandj.com - Aggressor™ Instruction Manual Page 3
Power Supply:
Before plugging your unit in, be sure the source volt-
age in your area matches the required voltage for your American DJ
®
Aggressor.™ The American DJ
®
Aggressor
™
is available in a 120v and
220v version. Because line voltage may vary from venue to venue, be
sure to plug your fi xture into a wall outlet with a matching power supply
before attempting to operate.
Aggressor™
Power Supply
• 48 Vibrantly Colored Beams.
• Easy Lamp Replacement.
• Fan Cooled.
• Bright LL-64514 120v/300w Lamp.
• Sound-Active
Aggressor™
Features
