background image

©American Audio®  -  www.americanaudio.com  -  V-01 Series™ Power Amplifier User Manual  Page 9

25. AC Cord -

 

Plug this cable into a standard 110~120v wall outlet. Check that the voltage in your area matches the amplifiers required voltage. 

26. Channel 2 Speakon Output -

 

Optional speaker output connections. Use pins 1+ and 1- of this 4-pole Speakon connector to connect to your 

speaker’s Speakon input jack.

27. Channel 2 Output Jack/5 way Binding Post -

 

Connect to your speaker’s input jack. Red is positive signal and Black is negative signal.

28. Ground Switch -

 

If hear a hum or any interference, put the Ground switch in the “On” postion .

29. Channel 2 Rear Gain Control -

 This rotary knob is used to control the output signal of channel two. Turning the knob in a clockwise direction 

will increase signal output. You must have the VOLUME CONTROL SWITCH in the “Rear” position to use this gain control.

30. Channel 2 Frequency Adjustment -

 

This knob is used to adjust the frequency level sent to your speaker on channel two when running the 

channel in subwoofer mode.

31. Volume Control Switch “Contractor Smart” - 

This switchs control of the amplifier’s volume control. The amplifier’s volume can be either con-

trolled from the rear of the unit or the front. If the switch is in the “Rear” position, the volume control located in the rear is used to control the volume. 
In this same postion the volume controls in the front of the unit will be disabled and cannot be used to adjust the volume. 

32. Channel 2 Subwoofer Mode On/Off Switch -

 

Turns the subwoofer mode for channel two on and off.

33. Channel 2 HPF (High Pass Filter) Switch - 

When this function is activated it removes all frequencies below 40Hz. Therefore the reproduction 

of the signal’s bass portion is optimized, since all ultra-low frequencies are eliminated.

34. Channel 2 Limiter Switch - 

This is used to activate the channels built-in limiter. The limiter reduces the average input level when the signal 

begins to distort, this process is designed to reduce distortion and protect the speakers. See limiter page 15.

35. Channel 2 XLR THRU Jack -

 

This jack is used to send a parallel signal from the channel two input jacks to another device or amplifier.

36. Channel 2 XLR Input -

 

Channel two balanced input jack. 

This combo jack will accept a standard 1/4 plug or XLR 3-pin balanced male 

plug.

 

Summary of Contents for V-01 Plus Series























Reviews: