background image

©American Audio®  -  www.americanaudio.com  -  V-01 Series™ Power Amplifier User Manual  Page 16

put). 

Short Circuit Protection

 can usually be traced back to the signal output line (i.e. speaker line). Check the line from the output ter-

minal of the amplifier to the speaker. If this line good, check the internal speaker connections and components. A short circuit will usu-
ally be traced to a bad cable or a bad speaker component and is rarely traced to the amplifier itself.

Thermal Protection -

 

Dual variable speed fans on the V-01 Series amplifier provide adequate cooling. During low level output the fans 

run at normal speeds. During high output and as heat raises, (exceeding 90°C.), the fans will run at higher speeds to aid the cooling 
process. If the heatsink temperature exceeds 91°C., the amplifier will mute until the amplifier cools down. When the amplifier cools 
below 90°C., the amplifier will return to normal operations. Be sure not to operate your amplifier below the minimum load ratings to 
reduce the risk of overheating problems.

Input/Output Protection -

 

The input circuits are isolated by 10k resistors. An ultrasonic network uncouples 

RF 

from the output and 

helps keep the amplifier stable with reactive loads.  

Operating Voltage (AC Mains) -

 The serial number label indicates the correct AC main voltage. Connecting to the wrong voltage is 

dangerous and may damage the amplifier. Always be sure the source voltage for your areas matches the required voltage for your 
amplifier.

Gain Controls -

 The gain controls are located on the front panel and are calibrated in 2dB of attenuation from full gain. It is best to 

adjust the amplifier so no “hissing” is heard from speakers with no music being played, this will ensure the lowest possible distortion 
during normal operation. 

AMPLIFIER FEATURES:

THRU -

 Thru will allow the user to daisy-chain one amplifiers signal input into another amplifier. Plug the signal source outputs into the 

first amplifier’s input, patch from the amplifier’s THRU jacks to the next amplifier’s input, and so on, daisy-chaining as many amplifiers 
as there is no excessive level loss. Is not affected by crossover setting.

GROUND LIFT SWITCH -

 Applying or lifting the ground switch will change the level for background noise and hum, if the noise level 

remains the same in either position, it is better to keep the ground lift switch in the ground position. This will eliminate 60Hz cycle hum 
that is sometimes induced when mounting several units in the same rack.

OPERATING VOLTAGE (AC MAINS) - 

The serial number label indicates the correct AC main voltage. Connecting to the wrong voltage 

is dangerous and may damage the amplifier.

GAIN CONTROLS -

 The gain controls are located on the front panel and are calibrated in 2dB of attenuation from full gain. It is best to 

adjust the amplifier so no “hissing” is heard from speakers with no music being played, this will ensure the lowest possible distortion 
during normal operation.

LED INDICATORS - 

Each channel has five LEDS. Two LEDs indicate signal level activity; one green LED and one yellow LED. One red 

LED indicates signal clipping. One red LED indicates protections mode for shorts/ overload. One green LED indicates an active signal. 
Both channels will also share the center blue LED that indicate the amplifier operating mode.

Summary of Contents for V-01 Plus Series























Reviews: