Page -8-
Installation: Electrical - Receiver Power & Ground
WARNING!
Use ONLY a volt meter to check voltage
during installation and testing.
*Using a test light WILL damage the outputs!
R.E.S.C.U.E. Remote Control System
Manual C841.N2
(
-
)
Battery
(
+
)
#10 x 3/4” Screw
#10 3/16” Star Washer
#10 3/16” Ring Terminal
Vehicle Frame
Scrape paint and clean area before
installing ground screw.
Chassis Ground
12
11
10
09
08
07
06
05
04
03
02
01
PowerTouch Remote Control System
Series 914 RF Receiver
This device complies with FCC rules part 15.
Operation is subject to the following 2 conditions:
1) This device may not cause harmful interference
2) This device must accept any interference received
including that causing undesired operation
Flex Whip Antenna Cable
*Maximum output current 5 Amps. Over current will damage outputs.
1a Maximum
12
11
10
09
08
07
06
05
04
03
02
01
White/Tan
Purple
Tan
Green/Black
Yellow/Black
Green/Red
Yellow/Red
Empty
Orange
Black
Empty
Red
Ch 4 - Output, 5 amp
Power +12v - 5 amp
Ch 3 - Output, 5 amp
Ch 1 - Input for rr@g circuit (-)*
Ch 2 - Input for rr@g circuit (-)*
Ch 1 - Output, +12v, 5 amp
Ch 2 - Output, +12v, 5 amp
Empty
Do Not Use
Chassis Ground
Empty
Logic +12v
*RR@G - Reversal Rest @ Ground
Notes:
1) Channels 1 and 2 are momentary outputs as long as the button is pressed.
2) Channels 3 and 4 are factory set as momentary outputs as long as the button is pressed. These outputs can be
programmed as latching (push on - push off). Call the factory for program information at 1-800-294-2570
10a Maximum
1) Install Power
Connect the Red wire to a co12v battery power source. Note: For best performance, run a
clean +12v (14 gauge wire) directly from the battery or a fuse that is NOT supplying any power to
motors, lights or any other type of high current device.
2) Install Ground
Connect the Black wire to chassis ground
A) Scrape all paint and grease away from the body frame.
A loose chassis ground connection WILL cause intermittent operation of receiver.
B) Clean the area using an alcohol based cleaner to remove paint chips and grease.
C) Crimp a #10, 3/16” ring terminal onto the black ground wire.
D) Insert the ring terminal and a #10, 3/16” star washer over a 10x3/4” hex head,
self-tapping ground screw.
E) Tighten ground screw securely into clean frame area.
3) Install Outputs - Maximum output is 5 Amps per channel
A) Connect
only
One
Channel output wire at a time to a relay or function which uses 5 Amps
B) Solder connections and protect with shrink tube or use an 18g insulated butt terminal.
Channel
Channel 1
Channel 2
Channel 3
Output
RR@G
(+) positive
RR@G
(+) Positive
(+) Positive
Wire
Color
Green / Black
Green / Red
Yellow / Black
Yellow / Red
Tan
Max
Output
5 Amp
5 Amp
5 Amp
5 Amp
5 Amp
Pin
Position
09
07
08
06
10
4) Wiring Inspection
A) Check all wiring
connections visually
B) Check the polarity
of all wires
C) Tape off or remove
all unused wires.
Input
+
+
-
Wire Color
Red
Purple
Black
Max Input
1 Amp
(fused)
10 Amp
(fused)
1 Amp
(fused)
Pin Position
01
11
03
Logic Power
Relay Power
Ground
Orange - Pin 4 - Not Used
A loose or corroded chassis ground connection
WILL cause intermittent operation!
Ground
Toggle Switch
