manualshive.com logo in svg

AMD AMD-761, Software/Bios Design Manual

The AMD AMD-761 Software/Bios Design Manual is a comprehensive and informative guide that provides users with detailed instructions on optimizing and configuring their AMD-761 motherboard. This manual can be easily downloaded for free from manualshive.com, allowing users to enhance their system's performance effortlessly.

Share
Download
background image

Chapter 3

DDR SDRAM Interface

169

24081D—February 2002 

AMD-761™ System Controller Software/BIOS Design Guide

Preliminary Information

3.7

ECC and Memory Scrubbing

The AMD-761 system controller DDR SDRAM controller
supports error correcting code (ECC) and memory scrubbing.
The error correction capability allows the correction of single-
bit errors and the detection of multiple-bit errors in any
memory quadword. Data is only checked by the memory
controller during a read access. A data error may be due to a
faulted bit in the DDR device itself, or a faulted bit that
occurred during data transmissions from the DDR devices to
the AMD-761 system controller memory controller. To support
the ECC function, DIMMs must support additional storage for
the ECC check bits. When ECC is enabled, the system must
have all DDR DIMMs that are 72 bits wide (also called ECC
DDR DIMMs). The AMD-761 system controller DDR SDRAM
controller provides five ECC modes. All ECC modes work
correctly with either unbuffered or registered DDR DIMMs.
The five modes supported are:

„

ECC Disabled

„

High-Performance EC Mode (EC_HiPerf mode)—Error
Checking only, no correction, except to the AMD Athlon™
processor

„

High-Performance ECC Mode (ECC_HiPerf mode)—Error
Checking and Correction

„

ECC with Scrubbing (ECC_Scrub mode)—Error Checking
and Correction with Scrubbing

„

Diagnostic ECC mode (ECC_Diag)

Each mode is discussed below.

The ECC check bits that are stored in the additional DDR
devices on the DIMM are generated by the memory controller
(based on a Hamming code algorithm) and written into the
DIMMs check bit storage during a memory write operation
when any ECC function is enabled. A single byte of check bits
represents the associated quadword of data that is written into
memory.

Wh e n   a ny   E C C   m o d e   i s   e n ab l e d   a n d   a   re a d   a c c e s s   i s
performed, the memory controller internally generates check
bits based on the data value read (for each quadword of data
read) and compares it with the check bits read along with the

Summary of Contents for AMD-761









































































































































































































































































Reviews:

No comments

Related manuals for AMD-761

Magnescale MG10-P1 Instruction Manual preview
MG10-P1
Brand: Magnescale Pages: 132
C.Nord GSM Operation Manual preview
GSM
Brand: C.Nord Pages: 100
3Com CoreBuilder 9000 Getting Started Manual preview
CoreBuilder 9000
Brand: 3Com Pages: 78
Harmonic Drive LA Series Manual preview
LA Series
Brand: Harmonic Drive Pages: 25
Nelson MR Technical Application Manual preview
MR
Brand: Nelson Pages: 8
fakro ZWMA Programming And Usage Instructions preview
ZWMA
Brand: fakro Pages: 16
e-BLEACH infinity User Manual preview
infinity
Brand: e-BLEACH Pages: 24
Galaxy Control Systems 635 Series Worksheet preview
635 Series
Brand: Galaxy Control Systems Pages: 5
Lattice LatticeMico8 User Manual preview
LatticeMico8
Brand: Lattice Pages: 23
Lattice Semiconductor CrossLink-NX Quick Start preview
CrossLink-NX
Brand: Lattice Semiconductor Pages: 2
Lathem PC600 Series Quick Start Manual preview
PC600 Series
Brand: Lathem Pages: 4
tams elektronik HADES Manual preview
HADES
Brand: tams elektronik Pages: 36
Magellan K32IRF User Quick Reference Manual preview
K32IRF
Brand: Magellan Pages: 2
D+H RZN 4402-K V2 Original Instructions Manual preview
RZN 4402-K V2
Brand: D+H Pages: 32
IBA MS8xICP Manual preview
MS8xICP
Brand: IBA Pages: 29
W.E.ST. SCU-138-P Technical Documentation Manual preview
SCU-138-P
Brand: W.E.ST. Pages: 34
Ltech TT-DX-R4-5A Manual preview
TT-DX-R4-5A
Brand: Ltech Pages: 4
Motor Guard M-60R Instructions preview
M-60R
Brand: Motor Guard Pages: 2

Brands by name

Popular brands

Load more brands