manualshive.com logo in svg

Ambirad ARO Series, Installation And Operating Manual, Page: 9 / 16

Share
Download
Ambirad ARO Series Installation And Operating Manual Download Page 9

Figure 7    Single Burner Installation (with part number identification)

Figure 8    Multiple Burner Installation (with part number identification)

Oil
Lifter

Oil Storage

Tank

Fire Protection
200137 -15*
* If total length
of capillary is
greater than 15m
to burner use
200251/252+
200143

200138

200141/229

Isolating

valve

200147/146

Filter

Flue

Thermolink 200143

Flue

Terminal

201071 Filter

200141/229 Valve

Pressure setting 

valve

Burner

200mm 

to 

800mm

201076
Pressure Gauge

200140 

Transfer Pump

Schematic Multi Burner Installation

Pressure

Setting

Valve

Pressure

Gauge

201072/073/

074

Back 

pressure

relief valve

200251/252

Solenoid Firevalve

200147/146 

Filter

200141/299

Isolating Valve

200148 De-Aerator

c/w combined valve

Schematic Single Burner Installation

(With Part No Identification)

(With Part No Identification)

Burner

Flue

Terminal

200mm

to

800mm

300mm to 2500mm

4m - 8m

7

Summary of Contents for ARO Series

















Reviews:

No comments