background image

Description of each symbol:

      : High setting: when the high setting is selected, the “      ” digit in the display will illuminate.

      : Low setting: when the low setting is selected the “      ” digit in the display will illuminate.

      : Timer, When the ON/OFF timer is set to ON, the      will illuminate.

      : When setting the temperature or timer, the      digits will flash.

      : Displays the current room temperature.

Turning on the heater:

Plug the heater into the mains supply; press the main “I /0” switch to the " I " position, then press the      button to turn 

the heater ON. Press the      button again to turn the heater OFF.

Setting the temperature:

In order to set the temperature, the heater has to be working at heating mode: High or Low. Press the "+" or "-" button, 

the temperature       digit will flash, continue to press the "+" or "-" button to set the desired temperature ( temperature 

range:5 - 35 

). After about 5 seconds without pressing, the display will show the current temperature , now the 

desired temperature is set.

NOTE: If the current temperature is higher than the set temperature ,the heater will stop working, for example, you set 

20

, but room temperature is 25

, the heater will not work.

Select the heat setting.

There are two heat settings on this heater( the default setting is High),press the “M” button to select the heating setting.

1. High: 1500w,       will illuminate.

2. Low: 750w,      will illuminate.

Timer setting:

A: Setting the timer to turn heater ON automatically:

In order to set this function, the heater must be turned off firstly. Press the timer button     ,      will illuminate and “0” will 

flash on the display. Press “+” or “-“button to set the desired time (0-24hrs) for the heater to turn on automatically. After 

the time is set ,the room temperature will show on the display.

B: Setting the timer to turn heater OFF automatically:

In order to set this function, heater must be working status. Press the timer button     ,      will illuminate and “0” will flash 

on the display. Press “+” or “-“button to set the desired time (0-24hrs) for the heater to turn off automatically . After the 

time is set, the room temperature will show on the display.

C: Cancelling a timer setting:

When the timer indicator is illuminated, pressing the      button will cancel the timer setting.

D: Checking the ON/OFF time:

When the ON/OFF timer is set, press the      to check the time setting.

Using the remote control

There are six function buttons on remote control, function are as follows:

 

 

SYMBOL

FUNCTION

Display & function ON/OFF

Heating mode: HigH/Low

Timer setting

Increase the temperature and timer setting

Decrease the temperature and timer setting

7

Summary of Contents for NDK15-12K










Reviews: