Amano PE225BU DUST CONTROL, Operator'S Manual

Page: 14 / 32

14
Section - A English - EN
Problem Possible Cause Solution
Check the main power supply (building circuit breaker).
Check the cord connection at the wall outlet
Switch lever safety lock not depressed Hold in the switch lever safety lock and then engage switch levers.
Bad connection Check the motor and cord interlock connections.
Defective motor start switch Contact an authorized APEC Distributor.
Using extension cord with wire smaller than 12/3. Replace with a 12/3 extension cord.
Using more than one extension cord. Only use one 50ft 12/3 extension cord.
Bad motor run capacitor Contact an authorized APEC Distributor.
Handle is not locked Push down on handle release lever to lock handle.
Defective handle switch Contact an authorized APEC Distributor.
Eliminate extension cord & locate a power source closer to work site.
Have voltage checked by a qualified electrican.
Not on a dedicated circuit Make sure there is no other items using power on the circuit.
Try a different pad that is less aggressive.
DO NOT add weight to machine. Remove any excess weight added to machine.
Bad connection Contact an authorized APEC Distributor.
Handle is not locked Push down on handle release lever to lock handle.
Defective motor Contact an authorized APEC Distributor.
Defective pad One side is more dense than the other. Replace pad.
Warped or damaged padholder Replace.
Pad not installed properly / not centered Remove and install properly.
The floor was not cleaned before buffing. Scrub and clean the floor.
Clean the pad or replace with a new clean pad.
There floor does not shine Use the appropriate pad for the job.
Poor Performance
There are lines on the floor
Machine vibrates during
operation
Machine will not start
No power
Motor runs sluggish
Low voltage
Fuse / circuit breaker
repeatedly trips
Low voltage
Motor is overloaded
Problem Possible Cause Solution
Check the main power supply (building circuit breaker).
Check the cord connection at the wall outlet
Switch lever safety lock not depressed Hold in the switch lever safety lock and then engage switch levers.
Bad connection Check the motor and cord interlock connections.
Defective motor start switch Contact an authorized APEC Distributor.
Using extension cord with wire smaller than 12/3. Replace with a 12/3 extension cord.
Using more than one extension cord. Only use one 50ft 12/3 extension cord.
Bad motor run capacitor Contact an authorized APEC Distributor.
Handle is not locked Push down on handle release lever to lock handle.
Defective handle switch Contact an authorized APEC Distributor.
Eliminate extension cord & locate a power source closer to work site.
Have voltage checked by a qualified electrican.
Not on a dedicated circuit Make sure there is no other items using power on the circuit.
Try a different pad that is less aggressive.
DO NOT add weight to machine. Remove any excess weight added to machine.
Bad connection Contact an authorized APEC Distributor.
Handle is not locked Push down on handle release lever to lock handle.
Defective motor Contact an authorized APEC Distributor.
Defective pad One side is more dense than the other. Replace pad.
Warped or damaged padholder Replace.
Pad not installed properly / not centered Remove and install properly.
The floor was not cleaned before buffing. Scrub and clean the floor.
Clean the pad or replace with a new clean pad.
There floor does not shine Use the appropriate pad for the job.
Poor Performance
There are lines on the floor
Machine vibrates during
operation
Machine will not start
No power
Motor runs sluggish
Low voltage
Fuse / circuit breaker
repeatedly trips
Low voltage
Motor is overloaded
Problem Possible Cause Solution
Check the main power supply (building circuit breaker).
Check the cord connection at the wall outlet
Switch lever safety lock not depressed Hold in the switch lever safety lock and then engage switch levers.
Bad connection Check the motor and cord interlock connections.
Defective motor start switch Contact an authorized APEC Distributor.
Using extension cord with wire smaller than 12/3. Replace with a 12/3 extension cord.
Using more than one extension cord. Only use one 50ft 12/3 extension cord.
Bad motor run capacitor Contact an authorized APEC Distributor.
Handle is not locked Push down on handle release lever to lock handle.
Defective handle switch Contact an authorized APEC Distributor.
Eliminate extension cord & locate a power source closer to work site.
Have voltage checked by a qualified electrican.
Not on a dedicated circuit Make sure there is no other items using power on the circuit.
Try a different pad that is less aggressive.
DO NOT add weight to machine. Remove any excess weight added to machine.
Bad connection Contact an authorized APEC Distributor.
Handle is not locked Push down on handle release lever to lock handle.
Defective motor Contact an authorized APEC Distributor.
Defective pad One side is more dense than the other. Replace pad.
Warped or damaged padholder Replace.
Pad not installed properly / not centered Remove and install properly.
The floor was not cleaned before buffing. Scrub and clean the floor.
Clean the pad or replace with a new clean pad.
There floor does not shine Use the appropriate pad for the job.
Poor Performance
There are lines on the floor
Machine vibrates during
operation
Machine will not start
No power
Motor runs sluggish
Low voltage
Fuse / circuit breaker
repeatedly trips
Low voltage
Motor is overloaded
Machine Troubleshooting
Scheduled Maintenance
Daily Monthly
Every 6
Months
Check for loose or lost fasteners
l
Inspect cords and connections
l
Inspect pad holder for damage
l
Clean the machine and accessories
l
Check machine wiring for fray or cut
l
Check the carbon brushes of motor
l
Operation
Interval
These items must be performed with the proper tools and training. Contact an Amano
Pioneer Eclipse Factory Certified Technician unless you have the proper equipment and
technical proficiency.
Tripped circuit breaker Press reset button on circuit breaker (under rear of machine).