11
Programming
Preprogrammed Number Pads
Oven has 10 preprogrammed number pads. Model
LD510S, ULD510S has 20 programmable pads
(01-20).Follow instructions below to program heating
times and power levels for customized cooking.
1.
Open oven door.
• If door is closed or
STOP/RESET pad is pressed
before finishing programming sequence, oven exits
programming mode.
2.
Press and hold pad
1 for approximately 5 seconds.
• After 5 seconds, signal sounds. Display shows
“PROGRAM” indicating program mode..
3.
Press desired number pad.
• Display shows heating time, “COOK LEVEL” and
• For some models press 2 digits(01-20).
power level if other than 100 percent power.
4.
Press number pads to enter desired cooking time.
• For example, to heat for 2 minutes 30 seconds,
press
2, 3, and 0 pads.
5.
Press desired power level pad to change power level.
• Display shows current power level if other than 100
percent power.
6.
Press power level pad to enter desired power level.
• For example, pressing DEFROST/20% pad is
• The factory setting is 100%
20 percent power
7.
Press
STARTpad to save new heating time and power
level in over menory.
8.
Press
STOP/RESET
programming mode.
pad or close oven door to exit
X2 (Double Quanity Feature)
Model LD510S, ULD510S only. It allows the programmer
to change how much heating time is added when X2 pad
and then the preprogrammed pad is pressed. The X2 pad
can add from 10%-100% of additional heating time.
1.
Open oven door.
• If door is closed or STOP/RESET pad is pressed
before finishing programming sequence, oven exits
programming mode.
2.
Press pad hold pad
1 for approximately 5 seconds.
• After 5 seconds, signal sounds. Display shows
"PROGRAM" indicating program mode.
3.
Press desired number pad.
• Display shows heating time, and programmed number.
• For some models press 2 digits (01-20) number.
4.
Press X2 pad.
• CF:08 shows in display. "CF" represents "cooking
factor" and "08" indicates 80%.
5.
Press number pad to enter desired cooking factor.
• For example, pressing 2 pad is 20% (0=100%).
6.
Press
• Repeat step 3-6 to program additional pads.
START pad to save new cooking factor in oven
memory.
7.
Press
RESET pad or close oven door to exit
programming mode.
Multiple Heating Stages
Follow instructions below to program oven to perform 3
consecutive heating cycles without interruption.
1.
Open oven door.
• If door is closed or
STOP/RESET pad is pressed
before finishing programming sequence, oven exits
programming mode.
2.
Press pad
1 for approximately 5 seconds.
• After 5 seconds, signal sounds.
3.
Press desired number pad.
• Display shows heating time and preprogrammed
number.
4.
Press number pads to enter desired cooking time.
• For example, to heat for 2 minutes 30 seconds,
5.
Press desired power level pad to change power level.
• If a power level pad is not pressed, oven defaults to
100% power.
• For example, pressing MEDIUM 50% pad sets oven
to 50% power.
• Display shows current power level if other than 100
percent power.
6.
Press power level 9
• For example, pressing DEFROST 120% pad is 20
percent power.
• The factory setting is 100%.
• Display briefly shows "STAGE 2". Then cook time
and power level for stage show in display.
• Repeat steps 5-8 to create additional stages.
7.
Press
TIME ENTRY pad.
8.
Press
9.
Press
START
RESET
pad to save new heating time and
pad or close oven door to exit
programming mode.
power level in oven memory.
GB
