22
side (left side for counterflows) electrical connection with the
junction box located inside the burner compartment. To make
electrical connections through the opposite side of the fur-
nace, the junction box must be relocated to the other side of
the burner compartment prior to making electrical connections.
To relocate the junction box, follow the steps shown below.
NOTE:
Wire routing must not to interfere with circulator blower
operation, filter removal, or routine maintenance.
J
UNCTION
B
OX
R
ELOCATION
E
DGES
OF
SHEET
METAL
HOLES
MAY
BE
SHARP
. U
SE
GLOVES
AS
A
PRECAUTION
WHEN
REMOVING
HOLE
PLUGS
.
WARNING
T
O
PREVENT
PERSONAL
INJURY
OR
DEATH
DUE
TO
ELECTRIC
SHOCK
,
DISCONNECT
ELECTRICAL
POWER
BEFORE
INSTALLING
OR
SERVICING
THIS
UNIT
.
WARNING
HIGH VOLTAGE !
T
O
AVOID
THE
RISK
OF
INJURY
,
ELECTRICAL
SHOCK
OR
DEATH
,
THE
FURNACE
MUST
BE
ELECTRICALLY
GROUNDED
IN
ACCORDANCE
WITH
LOCAL
CODES
OR
IN
THEIR
ABSENCE
,
WITH
THE
LATEST
EDITION
OF
THE
N
ATIONAL
E
LECTRIC
C
ODE
.
WARNING
Line voltage connections can be made through either the
right or left side panel. The furnace is shipped conigured
for a right side electrical connection. To make electrical
connections through the opposite side of the furnace, the
junction box must be relocated to the left side prior to mak-
ing electrical connections. To relocate the juntion box, per-
form the following steps.
1. Remove the burner compartment door.
2. Remove and save the two screws securing the junction
box to the side panel.
3. Relocate junction box and associated plugs and
grommets to opposite side panel. Secure with screws
removed in step 2.
WARNING
T
O
AVOID
THE
RISK
OF
INJURY
,
ELECTRICAL
SHOCK
OR
DEATH
,
THE
FURNACE
MUST
BE
ELECTRICALLY
GROUNDED
IN
ACCORDANCE
WITH
LOCAL
CODES
OR
,
IN
THEIR
ABSENCE
,
WITH
THE
LATEST
EDITION
OF
THE
NATIONAL
E
LECTRICAL
C
ODE
.
To ensure proper unit grounding, the ground wire should run
from the furnace ground screw located inside the furnace junc-
tion box all the way back to the electrical panel.
NOTE:
Do not
use gas piping as an electrical ground. To confirm proper unit
grounding, turn off the electrical power and perform the fol-
lowing check.
1. Measure resistance between the neutral (white)
connection and one of the burners.
2. Resistance should measure 10 ohms or less.
This furnace is equipped with a blower door interlock switch
which interrupts unit voltage when the blower door is opened for
servicing. Do not defeat this switch.
24 V
OLT
T
HERMOSTAT
W
IRING
W
IRE
ROUTING
MUST
NOT
INTERFERE
WITH
CIRCULATOR
BLOWER
OPERATION
,
FILTER
REMOVAL
OR
ROUTINE
MAINTENANCE
.
A
REMOVABLE
PLUG
CONNECTOR
IS
PROVIDED
WITH
THE
CONTROL
TO
MAKE
THERMOSTAT
WIRE
CONNECTIONS
. T
HIS
PLUG
MAY
BE
REMOVED
,
WIRE
CONNECTIONS
MADE
TO
THE
PLUG
,
AND
REPLACED
. I
T
IS
RECOMMENDED
THAT
YOU
DO
NOT
CONNECT
MULTIPLE
WIRES
INTO
A
SINGLE
TERMINAL
. W
IRE
NUTS
ARE
RECOMMENDED
TO
ENSURE
ONE
18 AWG
WIRE
IS
USED
FOR
EACH
TERMINAL
. F
AILURE
TO
DO
SO
MAY
RESULT
IN
INTERMITTENT
OPERATION
.
STRONGLY
IMPORTANT NOTE
As a two-stage non-communicating furnace, the furnace inte-
grated control module provides terminals for both “W1” and
“W2”, and “Y1” and “Y2” thermostat connections. This allows
the furnace to support the following system applications: ‘Two-
Stage Heating Only’, ‘Two-Stage Heating with Single Stage Cool-
ing’, and ‘Two-Stage Heating with Two-Stage Cooling’. Refer to
the following figures for proper connections to the integrated
control module.
Low voltage connections can be made through either the right
or left side panel. Thermostat wiring entrance holes are located
in the blower compartment. The following figure shows connec-
tions for a “heat/cool system”.
This furnace is equipped with a 40 VA transformer to facilitate
use with most cooling equipment. Consult the wiring diagram,
located on the blower compartment door, for further details of
115 Volt and 24 Volt wiring.
NOTE:
For single stage cooling applications, a jumper may be
required between Y1 and Y2 at the furnace control in order to
achieve the desired single stage cooling airflow. Use of ramp-
ing profiles and dehumidification features require a jumper
between Y1 and O.
NOTE:
Thermostat “R” required if outdoor unit is equipped with
a Comfort Alert™ module or if the out door unit is a part of the
ComfortNet™™ family of equipment AND is wired as a non-
communicating system.
