12
Digital Dial Operation
Digital Dial option is available on some models only.
So...how do I use it?
(Digital Dial)
Heating
1.
Open oven door, place food in oven,
and close oven door.
2.
Turn time entry knob clockwise until
desired time displays.
• Factory default setting for cooking
time is 10 minutes. Cooking time can
be changed and set to 60 minutes.
(Refer to section on changing
options)
3.
Press a power level pad to change
power level, if desired. If no power
level is selected, unit will default to
100%.
• Power level can be set from full
power (100%), to 70%, 50% or
DEFROST (20%).
4.
Press
START
button.
• Oven begins operation and time
counts down.
5.
When cooking time has elapsed,
microwave energy stops and oven
signal sounds.
Numbered Pads
Display
Options (Factory Settings in Bold)
1
End of Cycle Beep
OP:10
OP:11
OP:12
3 second continuous beep.
Continuous beep until door is opened.
5 beep bursts until door is opened.
2
Speaker Volume
OP:20
OP:21
OP:22
OP:23
Eliminates beep.
Sets volume to low.
Sets volume to medium.
Sets volume to high.
3
Key Beep
OP:30
OP:31
Prevents beep when pad is pressed.
Allows beep when pad is pressed.
4
Keyboard Enable
Window
OP:40
OP:41
OP:42
OP:43
15 seconds after oven door is opened, keyboard disabled.
30 seconds after oven door is opened, keyboard disabled.
1 minute after oven door is opened, keyboard
disabled.
2 minutes after oven door is opened, keyboard disabled.
5
Add Time During
Heating
OP:50
OP:51
Prevents adding heating time while oven is heating.
Allows heating time to be changed while oven is
heating when a memory pad is pressed.
6
Reset Door Open
OP:60
OP:61
Allows oven to resume heating time countdown after door
is opened during cycle.
Cancels heating time count down after door is opened
during cycle.
7
(some models)
Maximum Heating Time
OP:70
OP:71
Allows 60 minutes of heating time.
Allows 10 minutes of heating time.
0
Clean Filter Message
OP:00
OP:01
OP:02
OP:03
Do not display message.
Display message for 24 hours every 7 days.
Display message for 24 hours every 30 days.
Display message for 24 hours every 90 days.
:30 QUICK SET Pad
Allows you to reheat for 30 seconds at 100% (full) power by simply pressing
the :30 QUICK SET pad. By repeatedly pressing this pad, you can extend the reheating time to
5 minutes by 30 second increments. To change the time assigned to this pad:
?
Can I change an option?
Options can be changed to suit individual preferences.
To change options:
Hidden
Pad
Interrupting Operation
Open oven door to interrupt operation or turn
time entry knob counterclockwise to “0”.
To resume microwave oven operation, close
door and press
START
.
If time was changed to “0”, time will need to be
reset, and then press
START
.
1.
Open oven door.
• If door is closed before programming is
complete, changes are discarded and
microwave exits options programming
mode.
2.
Press and hold the Hidden Pad for
approximately 5 seconds.
• This begins options programming
mode.
• Microwave will beep and
0P:--
0P:--
0P:--
0P:--
0P:--
appears in display.
3.
Press the Hidden Pad to advance to
the desired option to be changed.
• See table below for options.
4.
Turn Dial to change option setting.
•
0P:
0P:
0P:
0P:
0P:
and option number appear in
display.
• See table below for options.
5.
Press START pad to save changes.
• To change additional options, repeat
steps 2 - 5.
• Changes appear after door is
closed.
1.
Open oven door.
• If door is closed before programming is
complete, changes are discarded.
2.
Press and hold the :30 QUICK SET pad
for approximately 5 seconds.
• This activates the programming
mode.
• Microwave will beep and either
current or assigned time will show
in display.
3.
Turn Dial to change time setting.
• Time can be set from zero (0:00)
seconds to five minutes (5:00).
• If the assigned time is 0:00, the :30
QUICK SET pad is effectively
disabled.
4.
Press START pad to save changes.
Changing Time and
Power/Canceling
Mistakes
Heating time and power level can be changed
at any time while the oven is operating. Turn
knob to desired new setting. To set cooking
time to zero, turn knob counterclockwise to
“0”.
