background image

INSTALLATION CONSIDERATIONS

13

Safety

Please adhere to the following warnings and cautions when
installing, adjusting, altering, servicing, or operating the fur-
nace.

T

O PREVENT PERSONAL INJURY OR DEATH DUE TO IMPROPER INSTALLATION,

ADJUSTMENT, ALTERATION, SERVICE OR MAINTENANCE, REFER TO THIS

MANUAL. 

F

OR ADDITIONAL ASSISTANCE OR INFORMATION, CONSULT A

QUALIFIED INSTALLER, SERVICE AGENCY OR THE GAS SUPPLIER.

WARNING

WARNING

T

HIS PRODUCT CONTAINS OR PRODUCES A CHEMICAL OR CHEMICALS WHICH

MAY CAUSE SERIOUS ILLNESS OR DEATH AND WHICH ARE KNOWN TO THE

S

TATE OF 

C

ALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS OR OTHER

REPRODUCTIVE HARM.

 

WARNING

T

O PREVENT POSSIBLE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH

DUE TO ELECTRICAL SHOCK, THE FURNACE MUST BE LOCATED TO PROTECT

THE ELECTRICAL COMPONENTS FROM WATER.

Charge (ESD) Precautions
NOTE: 

Discharge body’s static electricity before touching

unit. An electrostatic discharge can adversely affect electri-
cal components.

Use the following precautions during furnace installation and
servicing to protect the integrated control module from dam-
age. By putting the furnace, the control, and the person at
the same electrostatic potential, these steps will help avoid
exposing the integrated control module to electrostatic dis-
charge. This procedure is applicable to both installed and
uninstalled (ungrounded) furnaces.

1. Disconnect all power to the furnace. Do not touch the

integrated control module or any wire connected to the
control prior to discharging your body’s electrostatic
charge to ground.

2. Firmly touch a clean, unpainted, metal surface of the

furnace near the control. Any tools held in a  person’s
hand during grounding will be discharged.

3. Service integrated control module or connecting wiring

following the discharge process in Step 2. Use caution
not to recharge your body with static electricity; (i.e., do
not move or shuffle your feet, do not touch ungrounded
objects, etc.). If you come in contact with an ungrounded
object, repeat Step 2 before touching control or wires.

4. Discharge any static electricity from your body to ground

before removing a new control from its container. Follow
Steps 1 through 3 if installing the control on a furnace.
Return any old or new controls to their containers before
touching any ungrounded object.

Product Application

This product is designed for use as a residential home gas
furnace. It is 

not

 designed or certified for use in mobile home,

trailer, or recreational vehicle applications.

This furnace can be used in the following non-industrial
commercial applications: Schools, Office buildings, Churches,
Retail stores, Nursing homes, Hotels/motels, Common or
office areas.  In all applications, the furnace must be installed
per the installation instructions.

Goodman

®

 brand G*SS9* and Amana

®

 brand A*SS9*  fur-

naces are ETL certified.  All furnaces are built for use with
Natural gas but can be converted for use with LP gas.

(

NOTE: 

If using propane gas, a propane conversion kit is

required).

Goodman

®

 brand G*SS9* and  Amana

®

 brand A*SS9*  high

efficiency furnaces are dual certified. Dual certification means
that the combustion air inlet pipe is optional and the furnace
can be vented as a:

Non-direct vent (single pipe) central forced air furnace
in which combustion air is taken from the installation
area or from air ducted from the outside or,

Direct vent (dual pipe) central forced air furnace in which
all combustion air supplied directly to the furnace burn-
ers through a special air intake system outlined in
this manual and the installation instructions.

To ensure proper installation, operation and servicing, thor-
oughly read the installation and service manuals for specif-
ics pertaining to the installation, servicing and application of
this product.

WARNING

P

OSSIBLE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH DUE TO FIRE,

EXPLOSION, SMOKE, SOOT, CONDENSTAION, ELECTRICAL SHOCK OR CARBON

MONOXIDE MAY RESULT FROM IMPROPER INSTALLATION, REPAIR, OPERATION,

OR MAINTENANCE OF THIS PRODUCT.

WARNING

T

O PREVENT PROPERTY DAMAGE, PERSONAL INJURY OR DEATH DUE TO FIRE,

DO NOT INSTALL THIS FURNACE IN A MOBILE HOME, TRAILER, OR RECREATIONAL

VEHICLE.

To ensure proper furnace operation, install, operate, main-
tain and service the furnace in accordance with the installa-
tion, operation and service instructions, all local building
codes and ordinances. In their absence, follow the latest
edition of the National Fuel Gas Code (NFPA 54/ANSI
Z223.1), and/or CAN/CGA B149 Installation Codes, local
plumbing or waste water codes, and other applicable codes.

A copy of the National Fuel Gas Code (NFPA 54/ANSI
Z223.1) can be obtained from any of the following:

Summary of Contents for ACSS9 Series




























































Reviews: