Alutherm heating B350 Instructions For User Download Page 10

Page: 10 / 60

ALUTHERM

Boilers 10

ALUTERM B 350 - 600

Installation, User and Service Manual

instructions for user

Heating

Alutherm B 350 - 600

4.2.3

Outside Temperature Control OTC (optional)

The boiler may use an outdoor sensor to provide weather compensation (OTC).

To activate weather compensation connect an oudoor sensor to numbers 5 and 6 on the terminal strip C2. Pin numbers 1 and 2 have to be bridged

by a wire. Alternatively those pin numbers (1 and 2) can be used for connecting room thermostat on/off. In the technician menu, under advanced CH

settings, CH request, OTC only must be selected. The outdoor sensor is then automatically detected by the controller. The parameters corresponding

with A-E in the figure below can be set in the technician menu (advanced CH settings).

A OTC offset: minimum CH setpoint value

B OTC setpoint maximum: maximum CH setpoint value

C OTC weather cold: external temperature value at which the maximum CH value will be used.

D OTC weather warm: external temperature value at which the minimum CH value will be used

E OTC warm weather shutdown: external temperature value at which the CH demand will end

In the user menu an eco setpoint reduction (night reduction) can be set.

Day, week and weekend options are also available (on, eco, off)

The outdoor sensor is available as an optional accessory.

The sensor should be installed on the north-side of the building at a height of approximately 2 meters.

Note : The resistance of the outdoor NTC should be 12 kOhm at 25 °C.

Also see table of resistance for NTC’s at 6.6.2

4.2.4

Optional digital communication

The boiler supports digital communication with room thermostats using Open-Therm communication protocols (automatically recognised if

connected to pins 1 + 2 on terminal strip C2, also see 4.2.1.)

CH Setpoint

Ext Temp

E D

Summary of Contents for B350





























































Search results

Summary of Contents for B350

Reviews:

Brands by name

Popular brands

Alutherm heating B350, Instructions For User

Search results

Summary of Contents for B350

Reviews:

Brands by name

Popular brands