background image

Page 7 of 11

EPH-N00-06003

5-20-97

9

 - 790 DOORS ONLY

Strip two clear vinyl jamb seals [L] into the

door panel [M] splash guard and the pivot jamb
[N] and trim flush at the ends.  Both vinyls should
be turned to trap water from the shower head.
Secure the vinyls with a small quantity of glue or
caulk at each end or by carefully crimping the
vinyl pocket.  Set the door panel aside.

Press the pivot jamb and strike jamb [P] (with
magnetic strip) over the two 135° posts [K].  Refer
to Step #1 for the proper handing of the door.

NOTE:  The magnetic strip on the strike jamb
must face the exterior and the clear vinyl jamb
seal on the pivot jamb must face inward.

10

 - 790 DOORS ONLY

Snap the fillers [R] into the curb assembly

[A] and header assembly [ D] between the door
jambs with the raised lip to the exterior and the
pivot holes toward the pivot jamb.  Center the curb
filler in the curb between the pivot and strike
jamb (use masking tape to hold in position).

NOTE:  The snap-in fillers should be exactly 3/8"
longer than the door panel width.

11

 - 790 DOORS ONLY

Pull the bottom end of the pivot jamb [N]

tight to the curb filler [R] and plumb the jamb.
Drill two 1/8" holes thru the pivot jamb and into
the 135° post [K] in line with the screws in the
header and approximately 1/4" vertically from the
ends of the jamb.  Drill a third hole centered
between the first two and enlarge the outer holes
with a 3/16" drill for clearance on the self-tapping
screws.  Attach the pivot jamb permanently with
three #8 x 1/4" truss head screws [C].

Slide the header filler [R] tight against the pivot
jamb.  Push the strike jamb [P] tight against the
fillers top and bottom.  With the pivot jamb plumb
and both fillers tight between the two door jambs,
the strike jamb also will be plumb and parallel to
the pivot jamb.  Attach the strike jamb to the other
135° post in the same manner as the pivot jamb.

Summary of Contents for Stickstall 794 Series












Reviews: