background image

Page 2 of 9

 

August 18, 2014 

Three-Year Limited Residential Warranty 

Alumax Bath Enclosures by Sapa is pleased to warrant to its dealers and residential customers that the 

products supplied by it shall be free from defects in material and workmanship for three (3) years from 

purchase of the product, provided they are installed and maintained according to the manufacturer’s 

recommended practices and installation instructions.

1

  The Alumax Limited Warranty applies to the original 

residential owner only, and is not transferable. 

Proof of Purchase and/or Registration of the product required for warranty coverage.   

Registration instructions accompany the product or available at www.alumaxshowerdoor.com. 

What Will Alumax Do? 

Alumax  will  repair  or  replace,  at  its  discretion,  any  product  found  to  be  defective  in  material  or 

workmanship  during  the  applicable  warranty  period.  Labor  is  not  included.  In  the  case  of  discontinued 

products  subject  to  warranty  coverage,  Alumax  reserves  the  right  to  substitute  comparable  product  of 

equivalent function. 

What is Not Covered? 

This limited warranty applies only to materials and workmanship supplied by Alumax.  This limited warranty 

does not cover glass (claims of glass breakage are excluded) or outside fabrication provided by others.  It 

excludes all wear items and does not cover defects caused by improper installation of the product.  Laws 

and building and safety codes governing the design and use of bathrooms vary widely.  Alumax does not 

control the selection of product, configurations, operating hardware or glazing materials, and assumes no 

responsibility for such.   

ALUMAX  DOES  NOT  MAKE  ANY  OTHER  REPRESENTATIONS  OR  WARRANTIES,  EXPRESS  OR 

IMPLIED,  INCLUDING,  BUT  NOT  LIMITED  TO,  ANY  IMPLIED  WARRANTY  OF  MERCHANTABILITY 

OR ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.  TO THE EXTENT ANY 

IMPLIED WARRANTIES ARE IMPLIED UNDER STATE LAW, SUCH WARRANTIES ARE LIMITED TO 

THE DURATION OF THE APPLICABLE LIMITED WARRANTY TIME FRAME OF THREE (3) YEARS.   

IN  NO  EVENT  SHALL  ALUMAX  BE  LIABLE  FOR  SPECIAL,  DIRECT,  INDIRECT,  OR 

CONSEQUENTIAL  DAMAGES,  INCLUDING,  BUT  NOT  LIMITED  TO,  LOSS  OF  USE  OR  PROFITS, 

PERSONAL INJURY, OR DAMAGE TO OTHER PROPERTY.

   

Some states do not allow the exclusion or limitation of implied warranties, or the exclusion or limitation of 

special, incidental or consequential damages, therefore these limitations and exclusions may not apply to 

you.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to 

state.

How do You Get Warranty Assistance? 

To make a claim under the terms of this Limited Warranty, contact your local Alumax Dealer or call or write 

Alumax Consumer Service at 800-643-1514, 248 W. Greene St., Magnolia, AR 71753.  Proof of Purchase 

and/or Registration of the product is required for warranty coverage.   

                                                 

1

 The manufacturer’s recommended practices and installation instructions are available at www.alumaxshowerdoor.com, by 

contacting your local Alumax Dealer, or by calling or writing Alumax Customer Service at 800-643-1514, 248 W. Greene St., 

Magnolia, AR 71753.   

Summary of Contents for ProLine PL60










Reviews: