- 2 -
SMP10C24X220 Series
Overview:
SMP10C24X220 Series units convert a 220VAC (working range 198VAC - 256VAC), 50/60Hz input into a regulated
24VDC @ 10A continuous supply current (see specifications).
SMP1024X220 Series Power Supply Configuration Reference Chart:
Altronix
Model Number
Accessory
Power
Distribution
Module(s)
Number
of
Output(s)
Fused
Outputs
PTC
Outputs
Individual
Output
Rating
(A)
Supervised
220VAC
50/60Hz
Input
Current
(A)
24VDC
Total
Output
Current
(A)
SMP10C24X220
----
1
----
----
10A
----
1.8A
10A
SMP10PMC24X220
P
SMP10PM24P4220
PD4
4
P
----
3.5A
SMP10PM24P4C220
PD4CB
----
P
2.5A
SMP10PM24P8220
PD8
8
P
----
3.5A
SMP10PM24P8C220
PD8CB
----
P
2.5A
SMP10PM24P16220
PD16W
16
P
----
3.5A
SMP10PM24P16C22 PD16WCB
----
P
2.5A
Specifications:
Installation Instructions:
Wiring methods should be in accordance with the National Electrical Code/NFPA 70/NFPA 72/ANSI and with all local
codes and authorities having jurisdiction. Product is intended for indoor use only.
1. Mount unit in the desired location. Mark and predrill holes in the wall to line up with the top two keyholes in the
enclosure. Install two upper fasteners and screws in the wall with the screw heads protruding. Place the enclosure’s
upper keyholes over the two upper screws; level and secure. Mark the position of the lower two holes. Remove the
enclosure. Drill the lower holes and install the three fasteners. Place the enclosure’s upper keyholes over the two
upper screws. Install the two lower screws and make sure to tighten all screws (Enclosure Dimensions, pg. 6).
Secure enclosure to earth ground.
2. Connect ground wire to the ground lug. Connect AC power to the terminals marked [L & N] (Fig. 1, pg. 4 or Fig. 4,
pg. 5). Use 18 AWG or larger for all power connections (Battery, DC output).
Keep power-limited wiring separate from non power-limited wiring (115VAC / 60Hz Input, Battery Wires).
Minimum 0.25” spacing must be provided.
CAUTION: Do not touch exposed metal parts. Shut branch circuit power before installing or servicing equipment.
There are no user serviceable parts inside. Refer installation and servicing to qualified service personnel.
3. Measure output voltage before connecting devices. This helps avoiding potential damage.
4. Connect devices to be powered:
a. For Power Supply Board connect to the terminals marked [--- DC +].
b. For Power Distribution Module(s) connect devices to be powered to the terminal pairs 1 to 4 marked
[1P & 1N] through [4P & 4N] (Fig. 2, pg. 4), 1 to 8 marked [1P & 1N] through [8P & 8N] (Fig. 3, pg. 4),
or 1 to 16 marked [1P & 1N] through [16P & 16N] (Fig. 5, pg. 5)
carefully observing correct polarity.
Input:
• Input 220VAC (working range 198VAC - 256VAC),
50/60Hz, 1.8A.
Output:
• 24VDC output.
• 10A supply current.
• Filtered and electronically regulated outputs.
• Short circuit and thermal overload protection.
Battery Backup:
• Built-in charger for sealed lead acid or gel type batteries.
• Maximum charge current 0.7A.
Battery Backup
(cont’d)
:
• Zero voltage drop when switching over to battery backup.
Supervision
(supervised models)
:
• AC fail supervision (form “C” contacts).
• Battery presence and low battery supervision
(form “C” contacts).
Visual Indicators:
• AC input and DC output LED indicators.
Enclosure Dimensions
(H x W x D)
:
13.5” x 13” x 3.25” (342.9mm x 330.2mm x 82.55mm)
- Accommodates up to two (2)12VDC/7AH batteries.
