background image

 

- 6 - 

MaximalRDV Rack Access Power Controllers (PTC)

WARNING: To reduce the risk of fire or electric shock, do not expose the unit to rain or moisture. 
This installation should be made by qualified service personnel and should conform to the National 
Electrical Code and all local codes.

The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user 
to the presence of an insulated DANGEROUS VOLTAGE within the product’s enclosure that may 
be of sufficient magnitude to constitute an electric shock .

The exclamation point within an equilateral triangle is intended to alert the user to the presence of 
important operating and maintenance (servicing) instructions in the literature accompanying 
the appliance .

CAUTION: To reduce the risk of electric shock do not open 
enclosure . There are no user serviceable parts inside . Refer servicing 
to qualified service personnel .

Power Supply Board Output Voltage Settings:

Maximal3RHDV, Maximal3RDV, 
Maximal33RDV 
Power Supply Boards

Maximal1RHDV, Maximal1RDV
Power Supply Board

Fig. 1

Fig. 1a

OFF - 24V

ON - 12V

ON

OFF - 24

V

ON - 12V

ON

ON

OFF - 24V

ON - 12V

Summary of Contents for Maximal1RDV













Reviews: