Overview:
ALTV615DC220 Series DC CCTV Power Supplies provide 6-15VDC distributed via fuse or PTC protected outputs for
powering CCTV cameras, heaters, and other video accessories.
ALTV615DC220 Reference Chart:
Altronix
Model Number
Output
Voltage
Total
Output
Current
(Power)
Number
of
Outputs
PTC
Protected
Outputs
Fuse
Protected
Outputs
Output
Current
(max per
output)
220VAC
50/60Hz
Input
Current
ALTV615DC44M220
6-15VDC
4A
4
-
P
3.5A
0.5A
ALTV615DC44CBM220
6-15VDC
4A
4
P
-
2.5A
0.5A
ALTV615DC48M220
6-15VDC
4A
8
-
P
3.5A
0.5A
ALTV615DC48CBM220
6-15VDC
4A
8
P
-
2.5A
0.5A
ALTV615DC416220
6-15VDC
4A
16
-
P
3.5A
0.5A
ALTV615DC416CB220
6-15VDC
4A
16
P
-
2.5A
0.5A
ALTV615DC616220
6-15VDC
6A
16
-
P
3.5A
1A
ALTV615DC616CB220
6-15VDC
6A
16
P
-
2.5A
1A
ALTV615DC1016220
6-15VDC
10A
16
-
P
3.5A
1A
ALTV615DC1016CB220
6-15VDC
10A
16
P
-
2.5A
1A
Specifications:
CAUTION: This installation should be made by qualified service personnel and should conform to the
National Electrical Code and all local codes.
Installation Instructions:
1. Mount unit in the desired location. Mark and predrill holes in the wall to line up with the top two keyholes in the
enclosure. Install two upper fasteners and screws in the wall with the screw heads protruding. Place the enclosure’s
upper keyholes over the two upper screws, level and secure. Mark the position of the lower two holes. Remove the
enclosure. Drill the lower holes and install the three fasteners. Place the enclosure’s upper keyholes over the two
upper screws. Install the two lower screws and make sure to tighten all screws (Enclosure Dimensions, pg. 7, 8).
2. Remove Power Distribution Module and isolation barrier (models with “M” suffix only).
3. Connect unswitched AC circuit (220VAC, 50/60Hz) as follows: Green branch wire (ground) connects to the terminal
marked , Line connects to the terminal marked [L], and Neutral connects to the terminal marked [N] of the Inlet
Appliance Connector. (Figs. 1-4, pgs. 4-6). Use 18 AWG or larger for all power connections.
Units with line cord installed skip Instruction #3.
Use 18 AWG or larger for all power connections. Connect green ground lead to earth ground
(Fig. 1-4, pgs. 4-6).
Keep power-limited wiring separate from non power-limited wiring. Minimum 0.25” spacing must be provided.
Use separate knockouts.
4. Adjust output voltage (unit is factory set at 12VDC): use the trimpot on the power supply board
prior to connecting CCTV devices.
5. Measure output voltage before connecting devices. This helps avoiding potential damage.
CAUTION: Determine the maximum operating voltage of the equipment being powered before adjusting the
output voltage.
- 2 -
ALTV615DC220 Series
Agnecy Listing:
• CE European Conformity.
Input:
• 220VAC (working range 198VAC-256VAC), 50/60Hz.
Output:
• Four (4), eight (8), or sixteen (16) individual outputs.
• 6VDC to 15VDC field adjustable.
• Outputs are rated @ 3.5A (fused) or 2.5A (PTC).
• Filtered and electronically regulated outputs.
Features:
• AC input and DC output LED indicators.
Features
(cont’d)
:
• Power ON/OFF switch.
• Unit maintains camera synchronization.
• Ease of installation saves time and eliminates
costly labor.
Enclosure Dimensions
(H x W x D approx.)
:
ALTV615DC44M220, ALTV615DC44CBM220,
ALTV615DC48M220, ALTV615DC48CBM220,
8.5” x 7.5” x 3.75” (215.9mm x 190.5mm x 95.25mm)
All other models:
13.5” x 13” x 3.25” (342.9mm x 330.2mm x 82.55mm)
Door
CAUTION: De-energize unit prior to servicing. For continued protection against fire hazard
replace fuse with the same type and rating. Do not expose unit to rain or moisture.
3.5A 250V
For continuous protection against
risk of fire replace fuses with
same type and rating.
common
outputs
protected
outputs
P
N
N
P
S
XFMR Inpu
t
PD16W
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
N
P
Wire Strap
(from
Enclosure
to Door)
XFMR
XFMR
Power Supply
Board
Used on PTC Models
(example: ALTV615DC416CB220)
P
N
PTCs
N
P
S
XFMR Input
PD16W
common
outputs
protected
outputs
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
P
N
DC outputs
DC outputs
Power
Switch
220VAC Input
50/60Hz
