manualshive.com logo in svg

Alto ENCORE L2426, Operator'S Manual, Page: 25 / 60

Share
Download
Alto ENCORE L2426 Operator'S Manual Download Page 25

CLARKE TECHNOLOGY Operator's Manual - Encore S2426/L2426

  Page  -25-

Clarke Technology

Encore S2426 and L2426

Accessories  -  5/01

A

CCESSORIES

Description

Part No.

Power Wand System Kit

10150A

Clarke Care Kit

14607A

39" Squeegee Assembly

10068A

32" Squeege Assembly

10129A

Poly Dur Protectant

50478A

Kit, Grease Gun

55420A

Kit, Low Voltage Shut-Off

14097A

Brake Kit Assembly "L"

10072A

Brake Kit Assembly "S"

10073A

Accessory Bag

30070A

Hour Meter Kit

10656A

Soft Caster Assembly

51092A

Gimbal, Brush "L"

833802

u

Gimbal, Brush Spring "L"

838301

u

Dual Direct Clutch Plate "S"

30034A

u

Spacer for 30034A Clutch Plate "S"

10143A

u

Center Lock Pad Retainer

56941A

u

Kit, Solution Fill

10177A

u

Brushes and  Pad Assemblies:

Size

Description

Part No.

Part No.

Used For

                              (Gimbal "L")   (Clutch "S")

13"

Polyproplene

11438A

10141A

General Scrubbing Hard Floors

13"

Pad Driver Asm.

17531A

10140A

Use for Pads

13"

Clean Grit

11439A

10152A

13"

Super Grit

11440A

10153A

13"

Nylon Soft

11437A

10154A

Squeegee Blades:
Description

32" Assembly

39" Assembly

Blade, Rear - Gum Rubber

30067A

30069A

Blade, Rear - Nitrile Solid

30081A

30082A

Blade, Rear - Ribbed Orange

30085A

30086A

Blade, Front - Ribbed Natural

30066A

30091A

Blade, Front - Slit Grout

30079A

30080A

Blade, Front - Ribbed Orange

30083A

30084A

NOTE: 

u

 indicates a change has been made since last publication of this manual.

Summary of Contents for ENCORE L2426





























































Reviews:

No comments