Alto ENCORE L2426 Operator'S Manual Download

Page: 15 / 60

CLARKE TECHNOLOGY Operator's Manual - Encore S2426/L2426

Page -15-

4. Disconnect the battery pack connector from the control

housing connector. See figure 14A.

5. Connect the DC connector on the charger to the battery

pack connector. See figure 14B.

6. Connect the charger to a properly grounded single phase

(3-wire) wall receptacle having the input voltage, fre-

quency, and ampere capacity specified on the nameplate

of the charger.

For more information on the use of the charger, read

the instructions supplied with the charger.

How To Adjust Brush Cleaning Path from 24" to 26"

1. Insure brush head is in up position.

2. Turn the key switch "OFF" and remove the key.

3. Open front cover.

4. Raise plunger pin and rotate brush head. See figure 15.

5. Insure plunger pin is engaged in brush plate.

6. Close front cover.

How To Install The Brushes Or Pad Drivers

To install the brushes or pad drivers on the machine,

follow this procedure:

1. Turn the key switch "ON".

2. Raise the brush head by pressing and holding the brush

switch until brush head is in its full up position.

3. Turn the key switch "OFF" and remove the key.

4. Go to the front of the machine and unlatch front cover, swing

cover open.

5. Unlatch right and left brush housings and remove them. See

figure 16.

6. Put a brush or pad driver under the brush motor plate. See

figure 17.

7. ("L" Model) Align the lugs on the motor gimbal with the slots

in the brush gimbal.

("S" Model) Align the lugs on the motor with the slots on the

brush gimbal.

8. ("L" Model) Pull the brush up until the gimbal locks.

("S" Model) Pull the brush up and rotate counter direction to

scrub rotation, until lugs lock.

9. Repeat steps 6, 7, and 8 to install the second brush or pad

driver.

10. Reinstall right and left brush housings and latch front cover.

DANGER: Operating a machine that is not completely

or fully assembled could result in injury or

property damage. Do not operate this

machine unless it is completely

assembled. Inspect the machine carefully

before operation.

How To Prepare the Machine For Operation

Figure 14A

Figure 14B

Figure 15

Figure 16

Figure 17

Summary of Contents for ENCORE L2426





























































Search results

Summary of Contents for ENCORE L2426

Reviews:

Related manuals for ENCORE L2426

Brands by name

Popular brands

Alto ENCORE L2426, Operator'S Manual

Search results

Summary of Contents for ENCORE L2426

Reviews:

Related manuals for ENCORE L2426

Brands by name

Popular brands