Altman SS-UV30 Manual For Use And Maintenance Download Page 4

I N S T A L L A T I O N   A N D   I N S T R U C T I O N   M A N U A L  

 

4

 

 

SETUP AND INSTALLATION 

Unpacking 

Remove  the  SS-UV30  lighting  fixture  from  its  shipping  box.    Set  the  unit  down  on  a  flat  surface  before 
proceeding.   

Lamping and Re-lamping 

The SS-UV30 lighting fixture is provided with (3) integral UV LED light modules. Under normal operating 
conditions, the UV LED light modules should have a rated life expectancy of over 50,000 hours. There are no 
user serviceable parts inside. The entire UV LED assembly will need to be changed. 

Mounting the fixture 

For ceiling mounting, install the Yoke and a Pipe Clamp if desired. Loosen the bolt on the pipe clamp mounted 
on top of the fixture yoke until the clamp fits snugly around the mounting pipe.  Make sure the clamp wraps 
securely around the pipe surface.  Tighten up the bolt securely to the pipe.  Next, loop the safety cable around 
the pipe and yoke, and then clip it back onto the cable itself.  For stand mounting, remove the Pipe Clamp and 
rotate the Yoke to the bottom of the fixture. Secure the Yoke to the stand with a bolt and washer.  For floor 
mounting, adjust the yoke to the bottom so the fixture frame and the yoke securely hold the UV fixture.   

Connecting power to the fixture 

Plug the fixture into a grounded receptacle connected to a circuit breaker.  Connect DMX signal to the fixture. 

Focusing the fixture 

With the fixture energized, point the unit in the direction of the object to be illuminated.  Adjust the yoke to the 
desired position and secure the fixture with the two handles provided on either side of the yoke.  Adjust the 

individual UV LED light modules to the desired focus and beam coverage.  Using a tool, lock down the UV 
LED light modules.

 

Cleaning the fixture 

Routine cleaning of the SS-UV30 lighting fixture will provide years of prolonged use.  Use compressed air to 
blow  off  any  dust  and  dirt  from  the  lens,  electronics  and  heat  sink.    For  the  lens,  use  a  soft  lint-free  cloth 
dampened with water to clean the lens of dust and dirt.  Dry off completely with compressed air or a dry lint-
free cloth.  

ETL FILE LISTING 

The  SS-UV30  lighting  fixture  is  ETL  and  c-ETL  pending  under  Altman  File  9700680  for  Portable  Electric 
Luminaires (UL Standard 153), Luminaires (UL Standard 1598) LED Equipment (UL Standard 8750). 

Summary of Contents for SS-UV30












Reviews: