background image

SPECIAL APPLICATION

400-0431-001

7

INSTALLING YOUR TP115-110

6

Step 1.

Determine

the

best location for the

TP115-110

and TP115-111. Where 

possible, locate the 

TP115-110

as close 

to the video source as possible and the 
TP115-111 as close to the receiving 
component as feasible.

Step 2.

Apply power to the 

TP115-110

using the 

power adaptor provided. The Power LED 
should be on and red.

Step 3.

Connect the video source to the input of 
the 

TP115-110

using a high quality video 

cable.

Step 4.

The Power LED should change from red 
to green indicating a signal is present.

Step 5.

Connect the audio input source to the 
audio jack on the 

TP115-110

Step 6.

Run a UTP  (CAT-5/CAT-5e) type cable 
from the 4TP OUTPUT of the 

TP115-110

transmitter to the 4TP INPUT on the 
TP115-111 receiver.

NOTE: Ensure good signal transmission 

by routing the cable so as to 
avoid any sharp angles, creases 
or bends.

Step 7.

Connect the 

TP115-111

video and audio 

outputs to their receiving devices.

NOTE:

Only the L+, L- and GND outputs 
on the 

TP115-111

terminal block 

output are active.

Step 8.

Apply power to the 

TP115-111

using the 

power adaptor provided. The Power LED 
should be on and red; green if a signal is 
present.

Step 9.

The units are now operational.

OPERATION

7

The 

TP115-110

requires only one adjustment to be 

made for optimal performance. The adjustment is
video equalization for long cable lengths.

7.1  VIDEO EQUALIZATION

Video equalization is provided to fine tune the 
displayed image on the remote display. 
Typically, for short cable runs the equalization 
will be set to near minimum. Cable lengths up to 
400 feet will require near maximum equalization.

The equalization adjustments on the 

TP115-110

and TP115-111

work together to provide 

equalization for maximum cable lengths. For 
example,  for  cable runs less than 50 feet, both 
equalization settings may be set to near
minimum. Cable runs of 400 feet will see 
equalization settings at about the three-quarter 
position.

TROUBLESHOOTING GUIDE

8

We have carefully tested and have found no 
problems in the supplied 

TP115-110.

However, we 

would like to offer suggestions for the following:

8.1 NO DISPLAY

Cause 1:

The source has a problem.

Solution:

Check the source and make sure 
there is a signal present and all 
source connections are correct. If 
the source is working and there is 
still no display, see Cause 2.

Cause 2:

The path has a problem.

Solution:

Connect the transmitter directly to 
the receiver using a short UTP 
patch cable. If the image is good, 
there is a problem with the cable. 
Otherwise, see Cause 3.

Cause 3:

Cable connections are incorrect.

Solution:

Make sure that cables are properly 
connected. Also, make sure that the 
continuity and wiring are good. If 
there is still no display present, see 
Cause 4.

Summary of Contents for TP110










Reviews: