background image

                                                         MULTI-TASKER

1

                       TABLE OF CONTENTS

                                                                             Page

PRECAUTIONS / SAFETY WARNINGS .............. 2

1.1 GENERAL................................................... 2

1.2 INSTALLATION .......................................... 2

1.3 CLEANING.................................................. 2

1.4 FCC / CE NOTICE ...................................... 2

ABOUT YOUR MT108-102/(103) ......................... 3

TECHNICAL SPECIFICATIONS .......................... 3

DESCRIPTION OF MT108-102/(103) .................. 4

APPLICATION DIAGRAM .................................... 4

INSTALLING YOUR MT108-102/(103)................. 6

OPERATION (FOR MT108-103 ONLY) ............... 6

7.1  RS-232 CONTROL .................................... 6

7.2  DESCRIPTION OF COMMANDS............... 6

7.3  SUMMARY OF COMMANDS ................... 10

TROUBLESHOOTING GUIDE ........................... 11

8.1  LED IS NOT LIT....................................... 11

8.2  NO SOUND.............................................. 11

8.3  SOUND DISTORTION ............................. 11

8.4  SOUND LEVEL IS LOW .......................... 11

ALTINEX POLICY .............................................. 12

Summary of Contents for MULTI-TASKER MT108-102














Reviews: