manualshive.com logo in svg

Alti-2 D-90114, User Manual, Page: 9 / 59

Share
Download
Alti-2 D-90114 User Manual Download Page 9

 

 

 

 

 
 
D-90114 Manual, N3 User 
Rev G 

©2008, 2009 Alti-2, Inc 

Page 8 of 58 

5/27/2015 

 
 
 

 

 

 

Navigating Menus 

 
 

 

The basics… 
 

 

The top and bottom buttons – up and down, 
increase and decrease 

 

 

The middle button – select and go back 

 
The details…  

 

 

The menu scrolls and wraps.  So, once you scroll 
and reach the end of the menu items it wraps 
and goes back to the first item in the menu   

 

 

Use the top and bottom buttons to go up and 
down within a menu 

 

 

Use the top and bottom buttons to increase or 

decrease a value 

 

 

Holding the top or bottom buttons causes their 
action to repeat, except in the Jump Log 

 

 

In the Jump Log, press and hold the top button 
to view a previous jump; press and hold the 
bottom button to view the next jump 

 

 

To select an item press the middle button and 
release  

 

 

To go back to the previous screen press the 

middle button and hold it until the screen 
changes  

 

 

Summary of Contents for D-90114




























































Reviews:

No comments