AlterG Anti-Gravity Treadmill 400X User Manual Download Page 11

Page: 11 / 54

D000348-00 Rev. B

Setup and Installation

An AlterG qualified technician will install the AlterG Anti-Gravity Treadmill after delivery. Please make sure

that you inspect the Anti-Gravity Treadmill upon delivery for any damage that may have occurred during

transportation. Take pictures and immediately report any damage to the shipping company and AlterG.

When you sign for the shipment of your Anti-Gravity Treadmill, you are taking responsibility for any damage

that may occur before installation.

Electrical Requirements

The recommended electrical outlet/power source for the AlterG Anti-Gravity Treadmill is a 20 ampere,

220VAC @ 50/60 Hz dedicated circuit with ground. The plug supplied with the AlterG Anti-Gravity Treadmill

is designated by the NEMA configuration system as 6-20P. The corresponding receptacle for the plug is a

NEMA 6-20R.
International systems are shipped with the NEMA 6-20P. An appropriate plug for the country and facility in

question should be wired as follows:
Black Conductor: Line

Black Conductor: Line

Green/Yellow Conductor: Ground

Customer

Circuit

Via 400

Rating

Cable (mm

)

Connector

Type

Region

20A

16A

LAPP USA # 321203

ANIXTER # 4A-1203EC-UL

US,

Canada

16A

12.8A

≥ 1.5



2.5

LAPP USA # 321203

ANIXTER # 4A-1203EC-UL

EU (DEU)

13A

10.4A

≥ 1.5



2.5

LAPP USA # 321203

ANIXTER # 4A-1203EC-UL

32A

16A

2.5

LAPP USA # 321203

ANIXTER # 4A-1203EC-UL

No Plug Required on 20A Switch Spur

UK (ring)

32A

16A

≥ 4.0

IEC 60309 male plug

UK (ring)

Summary of Contents for Anti-Gravity Treadmill 400X























































Search results

Summary of Contents for Anti-Gravity Treadmill 400X

Reviews:

AlterG Anti-Gravity Treadmill 400X, User Manual, Page: 11 / 54

Search results

Summary of Contents for Anti-Gravity Treadmill 400X

Reviews: