Altera USB-Blaster User Manual Download Page 17

Altera Corporation 

2–7

December 2004

USB-Blaster Download Cable User Guide

USB-Blaster Download Cable User Guide

Revision History

The table below shows the revision history of this user guide.

How to Contact 
Altera

For the most up-to-date information about Altera products, go to the 
Altera world-wide web site at

 www.altera.com

. For technical support on 

this product, go to

 www.altera.com/mysupport

. For additional 

information about Altera products, consult the sources shown below.

Chapter

Date

Version

Changes Made

2

December 2004

1.2

Update to conditions in table 2-5.

All

November 2004

1.1

Re-release.

All

July 2004

1.0

Initial release.

Information Type

USA & Canada

All Other Locations

Technical support

www.altera.com/mysupport/ 

www.altera.com/mysupport/ 

(800) 800-EPLD (3753)
(7:00 a.m. to 5:00 p.m. Pacific Time)

(408) 544-7000 

(1)

(7:00 a.m. to 5:00 p.m. Pacific Time)

Product literature

www.altera.com 

www.altera.com 

Altera literature services

[email protected] 

(1)

[email protected] 

(1)

Non-technical customer 
service

(800) 767-3753
(7:00 a.m. to 5:00 p.m. Pacific Time)

(408) 544-7000 
(7:00 a.m. to 5:00 p.m. Pacific Time)

FTP site

ftp.altera.com 

ftp.altera.com 

Note to table:

(1)

You can also contact your local Altera sales office or sales representative. 

Summary of Contents for USB-Blaster



















Reviews: