Altera Arria V GZ User Manual Download | Manualshive

Page: 61 / 300

background image

Chapter 4: Parameter Settings

4–5

Device Identification Registers

November 2012

Altera Corporation

Arria V GZ Hard IP for PCI Express

f

For more information, refer to the

PCI-to-PCI Bridge Architecture Specification

Device Identification Registers

lists the default values of the read-only Device ID registers. You can use the

parameter editor to change the values of these registers. At run time, you can change
the values of these registers using the optional reconfiguration block signals. For more
information, refer to

“Hard IP Reconfiguration Interface” on page 6–45

Table 4–4. Base and Limit Registers

Parameter

Value

Description

Input/Output

Disable

16-bit I/O addressing
32-bit I/O addressing

Specifies the address widths for the

IO base

and

IO limit

registers.

Prefetchable memory

Disable

32-bit I/O addressing
64-bit I/O addressing

Specifies the address widths for the

Prefetchable Memory

Base

register and

Prefetchable Memory Limit

register.

Table 4–5. Device ID Registers

Register Name/

Offset Address

Range

Default

Value

Description

Vendor ID

16 bits

0x0000

Sets the read-only value of the

Vendor ID

register. This parameter can

not be set to 0xFFFF per the PCI Express Specification. Address:

.

Device ID

16 bits

0x0001

Sets the read-only value of the

Device ID

register. Address:

.

Revision ID

8 bits

0x01

Sets the read-only value of the

Revision ID

register. Address:

Class code

24 bits

0x000000

Sets the read-only value of the

Class Code

register. Address:

.

Subsystem
vendor ID

16 bits

0x0000

Sets the read-only value of the

Subsystem Vendor ID

register in the

PCI Type 0 Configuration Space. This parameter cannot be set to 0xFFFF
per the

PCI Express Base Specification 2.1

3.0

. Address:

.

Subsystem
Device ID

16 bits

0x0000

Sets the read-only value of the

Subsystem Device ID

register in the

PCI Type 0 Configuration Space. Address:

«
...
59
60
61
62
63
...
»

Summary of Contents for Arria V GZ













































































































































































































































































































Reviews:

No comments

Related manuals for Arria V GZ

Brand: Lanpro Pages: 5

Brand: Cidron Pages: 27

Brand: Advantech Pages: 2

Brand: Advantech Pages: 2

Brand: Digital Equipment Pages: 36

NVIDIA GeForce PX8000

Brand: Jaton Pages: 42

Brand: Gigabyte Pages: 35

ATI Radeon HD 3800 Series

Brand: AMD Pages: 28

Brand: Magtek Pages: 2

Brand: Nvidia Pages: 1

iCLASS SE Biometric Reader

Brand: HID Pages: 50

Brand: ZKTeco Pages: 7

UHF10F Pro Reader

Brand: ZKTeco Pages: 25

Brand: Planet Pages: 2

Brand: Planet Pages: 14

Brand: Videofied Pages: 6

Brand: Viking Pages: 4

Brand: FAMOCO Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands